Related papers: Fracture of bio-cemented sands
The purpose of this paper is to propose a continuum micromechanics model for the simulation of uniaxial compressive and tensile tests on lime-based mortars, in order to predict their stiffness, compressive and tensile strengths, and tensile…
The effect of substrate was studied using nanoindentation on thin films. Soft films on hard substrate showed more pile up than usual which was attributed to the dislocation pile up at the film substrate interface. The effect of tip blunting…
In this work, a combined modelling approach for crack propagation in defective graphene is presented. Molecular dynamics (MD) simulations are used to obtain material parameters (Young's modulus and Poisson ratio) and to determine the energy…
The fracture toughness for a mode I/II crack propagating in a ductile material has been subject to numerous investigations. However, the influence of the material hardening law has received very limited attention, with isotropic hardening…
The frictional properties of individual carbon nanotubes (CNTs) are studied by sliding an atomic force microscopy tip across and along its principle axis. This direction-dependent frictional behavior is found to correlate strongly with the…
The purpose of this paper is to propose an inexpensive micromechanics-based scheme for stiffness homogenization and strength estimation of mortars containing crushed bricks, known as cocciopesto. The model utilizes the Mori-Tanaka method to…
Static and dynamic analysis of the fracture tests of fiber composites in hydraulically servo-controlled testing machines currently in use shows that their grips are much too soft and light for observing the postpeak softening. Based on…
In this paper, we extend a micromechanics-based phase-field framework for fatigue fracture to incorporate cyclic plasticity with ratcheting. This mechanism is particularly relevant for low-cycle fatigue, where the accumulation of inelastic…
This paper unravels micromechanical aspects of metallic materials whose microstructure comprises grains of two or more phases. The local plastic response is determined by (i) the relative misorientation of the slip systems of individual…
A novel FFT-based phase-field fracture framework for modelling fatigue crack initiation and propagation at the microscale is presented. A damage driving force is defined based on the stored energy and dislocation density, relating…
In the context of the Damage Mechanics Challenge, we adopt a phase-field model of brittle fracture to blindly predict the behavior up to failure of a notched three-point-bending specimen loaded under mixed-mode conditions. The beam is…
The size effect on the fracture process zone in notched and unnotched three point bending tests of concrete beams is analysed by a meso-scale approach. Concrete is modelled at the meso-scale as stiff aggregates embedded in a soft matrix…
This paper presents fracture response of alkali-activated slag (AAS) mortars with up to 30% (by volume) of slag being replaced by waste iron powder which contains a significant fraction of elongated particles. The elongated iron particles…
An innovative technique, called conversion, is introduced to model circumferential cracks in thin cylindrical shells. The semi-analytical finite element method is applied to investigate the modal deformation of the cylinder. An element…
A continuum model of fracture that describes, in principle, the propagation and interaction of arbitrary distributions of cracks and voids with evolving topology without a fracture criterion is developed. It involves a 'law of motion' for…
An elastic-visco-plastic thermomechanical model for the simulation of cold forming and subsequent sintering of ceramic powders is introduced and based on micromechanical modelling of the compaction process of granulates. Micromechanics…
This study investigated, experimentally and numerically, the fracturing behavior of thermoset polymer structures featuring cracks and sharp u-notches. It is shown that, even for cases in which the sharpness of the notch would suggest…
The fundamental problem of friction in the presence of macroscopic adhesion, as in soft bodies, is receiving interest from many experimentalists. Since the first fracture mechanics `purely brittle' model of Savkoor and Briggs, models have…
In this work, we present crack propagation experiments evaluated by digital image correlation (DIC) for a carbon black filled ethylene propylene diene monomer rubber (EPDM) and numerical modeling with the help of variational phase-field…
Cement production, exceeding 4.1 billion tonnes and contributing 2.4 tonnes of CO2 annually, faces critical challenges in quality control and process optimization. While traditional process models for cement manufacturing are confined to…