Related papers: Achieving 45% efficiency of CIGS/CdS Solar Cell by…
Photogalvanic solar cells, the original dye based solar cell, have yet to fulfill their promise as a low fabrication cost, scalable energy conversion system. The efficient performance of photogalvanic cells relies on high dye solubility and…
To date, high efficiency multijunction solar cells have been developed on Ge or GaAs substrates for space applications, and terrestrial applications are hampered by high fabrication costs. In order to reduce this cost, we propose a…
Multijunction solar cells are usually grown on Ge substrates. This implies several disadvantages that hinder the performance of the whole multijunction and limit their possible applications. The drawbacks caused by the substrate are:…
Solar modules are currently characterized at standard test conditions (STC), defined at 1000W/m2 and 25 {\deg}C. However, solar modules in actual outdoor operating conditions typically operate at lower illumination and higher temperature…
Solution-processed quantum dots (QDs) have a high potential for fabricating low cost, flexible and large-scale solar energy harvesting devices. It has recently been demonstrated that hybrid devices employing a single monovalent cation…
Recombination through quantum dots (QDs) is a major factor that limits efficiency of QD intermediate-band (IB) solar cells. Our proposal for a new IB solar cell based on type-II GaSb QDs located outside the depletion region of a GaAs…
New generation Indium based lead-free Cs2InAgCl6 is a promising halide material in photovoltaic applications due to its good air stability and non-toxic behavior. But its wide band gap (>3 eV) is not suitable for solar spectrum and hence…
The performance of a combined solar photovoltaic (PV) and thermoelectric generator (TEG) system is examined using an analytical model for four different types of commercial PVs and a commercial bismuth telluride TEG. The TEG is applied…
We report an improved device fabrication process employed in the development of an advanced front contact grid design employing external busbars. The advanced fabrication process results in enhanced solar cell performance measured at…
Selenium, the world's oldest photovoltaic material, has experienced a renaissance in research over the past decade, with certified solar cell efficiencies climbing from the historical record of 5% to breaking the 10% barrier. Its wide…
Here we investigate the use of single-junction InGaAs airbridge cells (ABCs) at elevated power densities. Such conditions are relevant to many thermophotovoltaic (TPV) applications, ranging from space to on-demand renewable electricity, and…
Following the recent success of monolithically integrated Perovskite/Si tandem solar cells, great interest has been raised in searching for alternative wide bandgap top-cell materials with prospects of a fully earth-abundant, stable and…
To advance knowledge of K bonding in Cu(In,Ga)(Se,S)2 (CIGS) photovoltaic (PV) absorbers, recent Cu-K-In-Se phase growth studies have been extended to PV performance. First, the effect of distributing K throughout bulk Cu1-xKxInSe2…
We report the first empirical efficiency measurement of germanium-based thermophotovoltaic devices under high-temperature, high-irradiance conditions using a high view-factor calorimetric setup. Two TPV cell architectures were fabricated on…
The incoherence of sunlight has long been suspected to have an impact on solar cell energy conversion efficiency, although the extent of this is unclear. Existing computational methods used to optimize solar cell efficiency under incoherent…
Aluminum Indium Nitride (AlInN) alloys offer great potential for photovoltaic devices thanks to their wide direct bandgap energy that covers the solar spectrum from 0.7 eV (InN) to 6.2 eV (AlN), and their superior resistance to high…
Solution-processed, lead halide-based perovskite solar cells have overcome important challenges over the recent years, offering low-cost and high solar power conversion efficiencies. However, they still undergo unoptimized light collection…
We propose a novel approach to enhance the performance of perovskite solar cells (PSCs) by incorporating grated Cadmium Sulfide (CdS) and plasmonic gold nanoparticles (Au NPs) into the absorber layer. The CdS grating acts as the electron…
The demand for high-efficiency photovoltaic systems necessitates innovations that transcend the efficiency limitations of single-junction solar cells. This study investigates a tandem photovoltaic architecture comprising a top-cell with a…
Coating and reflecting thin films for energy harvesting purposes are interesting topics in both theoretical and experimental research. The thin film could help to enhance the absorption of the system via its specific optical properties…