Related papers: Enabling plastic co-deformation of disparate phase…
Al-Si alloys processed by laser rapid solidification yield eutectic microstructures with ultrafine and interconnected fibers. Such fibrous structures have long been thought to bear resemblance to those formed in impurity-doped alloys upon…
Initial powder mixtures of Cu, Fe and Co are exposed to severe plastic deformation by high-pressure torsion to prepare solid solutions. A broad range of compositions is investigated, whereas this study aims at the synthesis of soft magnetic…
Single-phase, multi-elements (three or more) with high concentrations show exceptional tensile strength up to ~ 0.8-1.2 GPa. However, they possess a very low 0.2% yield strength (YS), i.e., they can be permanently deformed at very…
A Cu-Cr composite was processed by severe plastic deformation to investigate the role of interphase boundaries on the grain size reduction mechanisms. The as-deformed material exhibits a grain size of only 20nm. This gives rise to a…
Silicon (Si) is one of the most abundant elements on Earth, and it is the most important and widely used semiconductor, constituting the basis of modern electronic devices. Despite extensive study, some properties of Si remain elusive. For…
It is now well established that materials are stronger when their dimensions are reduced to submicron scale. However, what happens at dimensions such as a few tens of nanometers or lower remains largely unknown, with conflicting reports on…
In the Cu Cr system, the formation of supersaturated solid solutions can be obtained by severe plastic deformation. Energy dispersive synchrotron diffraction measurements on as deformed Cu Cr samples as a function of the applied strain…
A filamentary composite elaborated by cold drawing was processed by High Pressure Torsion (HPT). The nanostructure resulting from this severe plastic deformation (SPD) was investigated thanks to scanning electron microscopy, transmission…
The two-phase composite approach of Estrin et al. (1998) describes an evolving dislocation cell structure. Mckenzie et al. (2007) enhanced the model to capture the effects of hydrostatic pressure and temperature during severe plastic…
We have investigated the nanostructure and microstructure resulting from ns laser irradiation simultaneous with deposition of Co films on Si(001) substrates. The spatial order and length scales of the resulting nanopatterns and their…
The processing of binary alloys consisting of ferromagnetic Fe and antiferromagnetic Cr by severe plastic deformation (SPD) with different chemical compositions has been investigated. Although the phase diagram exhibits a large gap in the…
When a material is subjected to an applied stress, the material will experience recoverable elastic deformation followed by permanent plastic deformation at the point when the applied stress exceeds the yield stress of the material.…
The fracture toughness of Al/SiC nanolaminates with different layer thicknesses (in the range 10 to 100 nm) was measured by means of micropillar splitting and bending of a notched beam. The crack plane was perpendicular to the layers in the…
This work gives insights into processing and characterisation of bulk nanocrystalline FeCr materials. The investigated FeCr alloys, consisting of 30, 50 and 70 at.% ferromagnetic Fe and remaining anti-ferromagnetic Cr, are processed by arc…
The interaction of crystalline defects leads to strain hardening in bulk metals. Metals with high stacking fault energy (SFE), such as aluminum, tend to have low strain hardening rates due to an inability to form stacking faults and…
Hot rolled commercial metastable austenitic steel 321 with strongly elongated thin delta-ferrite particles in its microstructure was the object of investigations. Ultrafine-grained (UFG) microstructure in steel 321 was formed by Equal…
In the present study, superheating treatment has been applied on A357 reinforced with 0.5 wt. % (Composite 1) and 1.0 wt.% (Composite 2) continuous stainless steel composite. In Composite 1 the microstructure displayed poor bonding between…
A Cu-Fe nanocomposite containing 50 nm thick iron filaments dispersed in a copper matrix was processed by torsion under high pressure at various strain rates and temperatures. The resulting nanostructures were characterized by transmission…
The deposition of Al film onto the (111) surface of a p-Si crystal was shown to induce a deformation in the near-surface layer of the latter. Provided that the crystal strain is elastic and uniaxial, the gettering of defects in the…
We reformulate the theory of polycrystalline plasticity, in externally driven, nonequilibrium situations, by writing equations of motion for the flow of energy and entropy associated with dislocations. Within this general framework, and…