Related papers: The ATLAS Readout System for LHC Runs 2 and 3
After the successful LHC operation at the center-of-mass energies of 7 and 8 TeV in 2010-2012, plans are actively advancing for a series of upgrades of the accelerator, culminating roughly ten years from now in the high-luminosity LHC…
In order to increase its discovery potential, the Large Hadron Collider (LHC) accelerator will be upgraded in the next decade. The high luminosity LHC (HL-LHC) period demands new sensor technologies to cope with increasing radiation…
The Pixel Detector of the ATLAS experiment has shown excellent performance during the whole Run-1 of LHC. Taking advantage of the long shutdown, the detector was extracted from the experiment and brought to surface, to equip it with new…
The design and performance of the inner detector trigger for the high level trigger of the ATLAS experiment at the Large Hadron Collider during the 2016-18 data taking period is discussed. In 2016, 2017, and 2018 the ATLAS detector recorded…
The Large Hadron Collider (LHC) was operated at a center-of-mass energy of $\sqrt{s}$ = 7 and 8TeV for proton-proton collisions in Run I. The CMS and ATLAS detectors both collected approximately 20 $fb^{-1}$ of 8TeV data in the data taking…
The Large Hadron Collider (LHC) at CERN is expected to be upgraded to the High-Luminosity LHC (HL-LHC) by 2029 and achieve instantaneous luminosity around 5 - 7.5 $\times$ 10$^{34}$cm$^{-2}$ s$^{-1}$. This represents a more than 3-4 fold…
The ATLAS High Level Trigger (HLT) consists of two selection steps: the second level trigger and the event filter. Both will be implemented in software, running on mostly commodity hardware. Both levels have a coherent approach to event…
RooFit and RooStats, the toolkits for statistical modelling in ROOT, are used in most searches and measurements at the Large Hadron Collider. The data to be collected in Run 3 will enable measurements with higher precision and models with…
This paper describes general characteristics of the deployment and commissioned of the Detector Control System (DCS) AD0 for the second phase of the Large Hadron Collider (LHC). The AD0 detector is installed in the ALICE experiment to…
Events containing a pair of high energy hadronic jet can provide clear signatures in the search for new physics at high energy hadron colliders. The ATLAS and CMS experiments collected the data from LHC collisions at $\sqrt{s}$= 13 TeV…
A summary of the on-going preparations from the ATLAS and CMS collaborations to perform top quark physics in Run II of the LHC and at the HL-LHC is given. To maintain the current level of precision and profit from the high-luminosity…
The Large Observatory for X-ray Timing (LOFT) is one of the four candidate ESA M3 missions considered for launch in the time-frame of 2022. It is specifically designed to perform fast X-ray timing and probe the status of the matter near…
The ATLAS experiment is designed to study the proton-proton collisions produced at the Large Hadron Collider (LHC) at CERN. Liquid argon sampling calorimeters are used for all electromagnetic calorimetry as well as hadronic calorimetry in…
The ATLAS experiment, at the Large Hadron Collider, will incorporate discrete, high-resolution tracking sub-systems in the form of segmented silicon detectors with 40MHz radiation-hard readout electronics. In the region closest to the pp…
The FASER experiment is a new small and inexpensive experiment that is placed 480 meters downstream of the ATLAS experiment at the CERN LHC. FASER is designed to capture decays of new long-lived particles, produced outside of the ATLAS…
In this work we present an experimental setup to show the suitability of ROS 2.0 for real-time robotic applications. We disclose an evaluation of ROS 2.0 communications in a robotic inter-component (hardware) communication case on top of…
The Phase-2 ATLAS upgrade for the High Luminosity Large Hadron Collider (HL-LHC) has motivated progressive redesigns of the ATLAS Tile Calorimeter (TileCal) read-out link and control board (Daughterboard). The Daughterboard (DB)…
The Tile Calorimeter at ATLAS is a hadron calorimeter based on steel plates and scintillating tiles read out by PMTs. The current read-out system uses standard ADCs and custom ASICs to digitize and temporarily store the data on the…
The CMS experiment will collect data from the proton-proton collisions delivered by the Large Hadron Collider (LHC) at a centre-of-mass energy up to 14 TeV. The CMS trigger system is designed to cope with unprecedented luminosities and LHC…
The CMS collaboration is building a new inner tracking pixel detector for the High-Luminosity LHC. Each pixel readout chip will be controlled with a single serial input stream at 160 Mbps and will send out data via four current mode logic…