Related papers: Advanced surface treatments for medium-velocity su…
We report the rf performance of a single-cell superconducting radiofrequency cavity after low temperature baking in a nitrogen environment. A significant increase in quality factor has been observed when the cavity was heat treated in the…
The performance of superconducting radio-frequency (SRF) cavities depends on the niobium surface condition. Recently, various heat-treatment methods have been investigated to achieve unprecedented high quality factor (Q) and high…
Vacuum thermal treatments (baking) are known to improve the superconducting properties of the RF surface layer of niobium cavities, and are employed as a last processing step to increase their efficiency determined by intrinsic quality…
The improvement of the quality factor Q0 of superconducting radio-frequency (SRF) cavities at medium accelerating gradients (20-25 MV/m) is important in order to reduce the cryogenic losses in continuous wave (CW) accelerators used for a…
The Medium temperature (mid-T) baking of niobium superconducting radio-frequency cavities at 300 350  C in a vacuum furnace is known to enhance the quality factor (Q₀). However, despite this improvement, cavities treated with…
Under-vacuum low- and mid-temperature baking revealed beneficial effects on the performance of niobium-made cavities for superconducting radio-frequency (SRF) applications, primarily seen in particle accelerators. Such a baking process is…
Medium temperature (mid-T) baking, typically conducted at 300 350 C, enhances the quality factor of niobium (Nb) superconducting radio frequency cavities. High vacuum furnace baking is commonly preferred for its practicality in large-scale…
The application of heat treatments on 1.3 GHz TESLA type cavities in ultra-high vacuum at 250{\deg}C to 350{\deg}C is called medium temperature or mid-T heat treatment. In various laboratories such treatments on superconducting radio…
The Continuous Electron Beam Accelerator Facility (CEBAF) was the first large-scale accelerator to employ superconducting radiofrequency (SRF) cavities for continuous-wave operation. Ongoing research and development efforts continue to…
We investigate the effect of high temperature treatments followed by only high-pressure water rinse (HPR) of superconducting radio frequency (SRF) niobium cavities. The objective is to provide a cost effective alternative to the typical…
Large-grain Nb has become a viable alternative to fine-grain Nb for the fabrication of superconducting radio-frequency cavities. In this contribution we report the results from a heat treatment study of a large-grain 1.5 GHz single-cell…
We report the RF performance of several single-cell superconducting radio-frequency cavities subjected to low temperature heat treatment in nitrogen environment. The cavities were treated at temperature 120 - 165 $^{\circ}$C for an extended…
We report a surface treatment that systematically improves the quality factor of niobium radio frequency cavities beyond the expected limit for niobium. A combination of annealing in a partial pressure of nitrogen or argon gas and…
Future particle accelerators such as the the SLAC ``Linac Coherent Light Source-II'' (LCLS-II) and the proposed Cornell Energy Recovery Linac (ERL) require hundreds of superconducting radio-frequency (SRF) cavities operating in continuous…
In this paper we present the discovery of a new surface treatment applied to superconducting radio frequency (SRF) niobium cavities, leading to unprecedented accelerating fields of 49 MV/m in TESLA-shaped cavities, in continuous wave (CW);…
We report the finding of new surface treatments that permit to manipulate the niobium resonator nitrogen content in the first few nanometers in a controlled way, and the resonator fundamental Mattis-Bardeen surface resistance and residual…
Niobium superconducting radiofrequency cavities enable applications in modern accelerators and quantum computers. However, the surface resistance significantly deteriorates the cavities performance. Nitrogen doping surface treatment can…
Mid-T heat treatments in the range from 250 to 400 C on superconducting radio-frequency (SRF) cavities have been shown to provide high quality factors that rise with applied rf field strength in high frequency, electro-polished (EP),…
High Q-factors are of utmost importance to minimize losses of superconducting radio-frequency cavities deployed in continuous wave particle accelerators. This study elucidates the surface treatment that can maximize the Q-factors in…
This comprehensive study, being part of the European XFEL R\&D effort, elucidates the influence of medium temperature (mid-T) heat treatments between 250{\deg}C and 350{\deg}C on the performance of 1.3~GHz superconducting radiofrequency…