Related papers: Fast and flexible data structures for the LHCb Run…
LHCb's Run 3 upgrade introduced a fully software-based trigger system operating at 30~MHz, processing an average of 5.6 proton-proton collision vertices per bunch crossing (event). This work presents the development of an inference engine…
An efficient and precise reconstruction of charged-particle tracks is crucial for the overall performance of the CMS experiment. During Run 2 of LHC, significant upgrades were made to the track reconstruction algorithms in order to…
A major LHCb detector upgrade will be installed during long shutdown~4 (LS4) of the CERN Large Hadron Collider. The experiment will operate at a maximum luminosity of up to $1.5\times 10^{34}\mathrm{cm}^{-2}\mathrm{s}^{-1}$, with acceptance…
The LHCb experiment at the Large Hadron Collider (LHC) is performing high precision measurements in the flavour sector. An excellent performance of the particle identification (PID) detectors as well as the development of new data taking…
The LHCb detector optimised its performance in Runs~1 and~2 by stabilising the instantaneous luminosity during a fill. This was achieved by tuning the distance between the two colliding beams according to the measurement of instantaneous…
In LHC Run 3, ALICE will increase the data taking rate significantly to 50 kHz continuous read-out of minimum bias Pb-Pb collisions. The reconstruction strategy of the online-offline computing upgrade foresees a first synchronous online…
ALICE has upgraded many of its detectors for LHC Run 3 to operate in continuous readout mode recording Pb--Pb collisions at 50 kHz interaction rate without trigger. This results in the need to process data in real time at rates 100 times…
For Run 3 (from 2021), the LHC will undergo a significant increase in instantaneous luminosity to 1.5 times its current value which will lead to larger collected statistics and an enhanced sensitivity to new physics. The Phase-1 upgrade of…
This article describes a custom VHDL firmware implementation of a two-dimensional cluster-finder architecture for reconstructing hit positions in the new vertex pixel detector (VELO) that is part of the LHCb Upgrade. This firmware has been…
LHCb is one of the major experiments operating at the Large Hadron Collider at CERN. The richness of the physics program and the increasing precision of the measurements in LHCb lead to the need of ever larger simulated samples. This need…
The LHCb experiment stores around $10^{11}$ collision events per year. A typical physics analysis deals with a final sample of up to $10^7$ events. Event preselection algorithms (lines) are used for data reduction. Since the data are stored…
The data acquisition system of the upgraded LHCb experiment includes the fast reconstruction of all hits in the vertex locator (VELO) pixel detector at the beam-crossing rate of 40 MHz, implemented as on-the-fly clustering embedded in the…
In 2019, the LHCb experiment at CERN will undergo a major upgrade where its detector electronics and the entire readout system will be replaced. The goal is to read-out all events at the full LHC frequency of 40 MHz, reaching a total data…
LHCb is a general purpose forward detector located at the Large Hadron Collider (LHC) at CERN. Although initially optimized for the study of hadrons containing beauty quarks, the better than expected performance of the detector hardware and…
The LHCb experiment is designed to perform high-precision measurements of CP violation and search for New Physics using the enormous flux involving beauty and charm quarks produced at the LHC. The operation and the results obtained from the…
LHCb is one of the four major experiments that will take data at the LHC, due to start operation in 2007. The primary aims of LHCb are to perform precision tests of CP violation and to search for new physics in b hadron decays. About 10^12…
After 2001 the upgraded ep collider HERA will provide an about five times higher luminosity for the two experiments H1 and ZEUS. In order to cope with the expected higher event rates the H1 collaboration is building a track based trigger…
A very compact architecture has been developed for the first level Muon Trigger of the LHCb experiment that processes 40 millions of proton-proton collisions per second. For each collision, it receives 3.2 kBytes of data and it finds…
In LHC Run 3, ALICE will increase the data taking rate significantly to 50\,kHz continuous read out of minimum bias Pb-Pb events. This challenges the online and offline computing infrastructure, requiring to process 50 times as many events…
The upgrade to the ATLAS trigger for LHC Run 2 is presented including a description of the design and performance of the newly reimplemented tracking algorithms. The profiling infrastructure, constructed to provide prompt feedback from the…