Related papers: Improved microwave SQUID multiplexer readout using…
We develop the concept of quasi-phasematching (QPM) by implementing it in the recently proposed Josephson traveling-wave parametric amplifier (JTWPA) with three-wave mixing (3WM). The amplifier is based on a ladder transmission line…
Microwave Kinetic Inductance Detectors (MKIDs) are the most attractive radiation detectors for far-infrared and sub-mm astronomy: They combine ultimate sensitivity with the possibility to create very large detector arrays, in excess of 10…
We present a readout method for superconducting flux qubits. The qubit quantum flux state can be measured by determining the Josephson inductance of an inductively coupled DC superconducting quantum interference device (DC-SQUID). We…
We have designed and demonstrated a Superconducting Quantum Interference Device (SQUID) array linearized with cryogenic feedback. To achieve the necessary loop gain a 300 element series array SQUID is constructed from three monolithic…
The Transition-Edge Sensors (TES) is a mature, high-resolution x-ray spectrometer technology that provides a much higher efficiency than dispersive spectrometers such as gratings and crystal spectrometers. As larger arrays are developed,…
Recent advancements in quantum technologies and advanced detection experiments have underscored the pressing need for the detection of exceedingly weak signals within the microwave frequency spectrum. Addressing this challenge, the…
We report on the noise of a lumped element Direct Current Superconducting Quantum Interference Device amplifier. We show that the noise temperature in the 4 GHz-8 GHz range over ranges of 10's of MHz is below 1 kelvin (three photons of…
We propose to use the quantum properties of a superconducting flux qubit in the construction of a magnetometer with quantum limited sensitivity. The main advantage of a flux qubit is that its noise is rather low, and its transfer functions…
We propose a flux-pumped superconducting parametric amplifier based on symmetrically threaded superconducting quantum interference devices (SQUIDs) that achieves a Kerr-free operating point under suitable drive conditions. Eliminating the…
Operating superconducting qubits at elevated temperatures offers increased cooling power and thus system scalability, but requires suppression of thermal photons to preserve coherence and readout fidelity. This motivates migration to higher…
Microwave Kinetic Inductance Detectors (MKIDs) have great potential for large very sensitive detector arrays for use in, for example, sub-mm imaging. Being intrinsically readout in the frequency domain, they are particularly suited for…
Superconducting quantum interference devices (SQUIDs) are among the most sensitive detectors for out-of-plane magnetic field components. However, due to their periodic response with short modulation period $M = 1 \Phi_0$, determined by the…
Inductance is a key parameter when optimizing the performance of superconducting quantum interference device (SQUID) magnetometers made from the high temperature superconductor YBa$_2$Cu$_3$O$_{7-x}$ (YBCO) because lower SQUID inductance…
We have developed a recently proposed Josephson traveling-wave parametric amplifier with three-wave mixing [A. B. Zorin, Phys. Rev. Applied 6, 034006, 2016]. The amplifier consists of a microwave transmission line formed by a serial array…
A digital frequency multiplexing (DfMUX) system has been developed and used to tune large arrays of transition edge sensor (TES) bolometers read out with SQUID arrays for mm-wavelength cosmology telescopes. The DfMUX system multiplexes the…
A quantum interface between microwave and optical photons is essential for entangling remote superconducting quantum processors. To preserve fragile quantum states, a transducer must operate efficiently while generating less than one photon…
We investigate the required peripheral circuits to enable ideal performance for a high-gain travelling-wave parametric amplifier (TWPA) based on three-wave mixing (3WM). By embedding the TWPA in a network of superconducting diplexers,…
Frequency domain multiplexing (fMux) is an established technique for the readout of transition-edge sensor (TES) bolometers in millimeter-wavelength astrophysical instrumentation. In fMux, the signals from multiple detectors are read out on…
As the field of quantum computing progresses to larger-scale devices, multiplexing will be crucial to scale quantum processors. While multiplexed readout is common practice for superconducting devices, relatively little work has been…
Dispersive readouts for superconducting qubits have the advantage of speed and minimal invasiveness. We have developed such an amplifier, the Cavity Bifurcation Amplifier (CBA) [10], and applied it to the readout of the quantronium qubit…