Related papers: Analog Cavity Emulators to Support LLRF Developmen…
Quantum transduction is a key technology for connecting different quantum technologies across varied frequencies. However, it remains a major challenge to overcome the high threshold for achieving positive capacity of traditional quantum…
CW magnetrons, developed for industrial heaters, but driven by an injection-locking signal were suggested to power Superconducting RF (SRF) cavities due to higher efficiency and lower cost of generated RF power per Watt than traditionally…
Length and g-factor are fundamental parameters that characterize optical cavities. We developed a technique to measure these parameters in-situ by determining the frequency spacing between the resonances of fundamental and spatial modes of…
Nearly concentric optical cavities can be used to prepare optical fields with a very small mode volume. We implement an anaclastic design of a such a cavity that significantly simplifies mode matching to the fundamental cavity mode. The…
The strength of optomechanical interactions in a cavity optomechanical system can be quantified by a vacuum coupling rate $\vcr$ analogous to cavity quantum electrodynamics. This single figure of merit removes the ambiguity in the…
Laser synchronization is a technique that locks the wavelength of a free-running laser to that of the reference laser, thereby enabling synchronous changes in the wavelengths of the two lasers. This technique is of crucial importance in…
Cavity quantum electrodynamics (cavity QED) enables the control of light-matter interactions at the single-photon level, rendering it a key component of many quantum technologies. Its practical realization, however, is complex since it…
The ISIS synchrotron at the Rutherford Appleton Laboratory in the UK now routinely uses a dual harmonic RF system to accelerate beam currents in excess of 230uA to run two target stations simultaneously. The acceleration in the ISIS…
The design of a 637-nm wavelength, photonic-integrated-circuit-based external cavity laser (PIC-based ECL) aimed at quantum technology applications is presented together with first experimental results. The PIC is designed to provide…
To increase the spectral efficiency of coherent communication systems, lasers with ever-narrower linewidths are required as they enable higher-order modulation formats with lower bit-error rates. In particular, semiconductor lasers are a…
Scaling superconducting quantum processors beyond single dilution refrigerators requires efficient optical interconnects, yet integrating microwave-to-optical (M2O) transducers poses challenges due to frequency mismatches and qubit…
Plasma based surface modification of niobium is a promising alternative to wet etching of superconducting radio frequency (SRF) cavities. The development of the technology based on Cl2/Ar plasma etching has to address several crucial…
It has recently been shown [Rossi et al., Phys. Rev. Lett. 119, 123603 (2017); ibid. 120, 073601 (2018)] that feedback--controlled in--loop light can be used to enhance the efficiency of optomechanical systems. We analyse the theoretical…
Precisely determining the gap voltage and phase in an RF cavity is essential for the calibration of the LLRF feedbacks. Following the conventional approach, measured RF power is converted into gap voltage, assuming a given shunt impedance.…
This letter presents a dual quadrature phasemeter, an implementation of a phase-locked loop designed to track the phase of homodyne and heterodyne inter-satellite laser links. The dual quadrature phasemeters use dual quadrature optical…
The generation of certifiable randomness is the most fundamental information-theoretic task that meaningfully separates quantum devices from their classical counterparts. We propose a protocol for exponential certified randomness expansion…
3D-printing of radiofrequency (RF) cavity resonators could provide a cost-effective solution that enables rapid prototyping and design flexibility compared to traditional fabrication of full-metal cavities. In this work, the feasibility of…
Cavity optoelectromechanical regenerative amplification is demonstrated. An optical cavity enhances mechanical transduction, allowing sensitive measurement even for heavy oscillators. A 27.3 MHz mechanical mode of a microtoroid was…
Utilizing the continuous frequency mode quantization scheme, we study from first principle the efficiency of a feedback scheme that can generate maximally entangled states of two atoms in an optical cavity through their interactions with a…
Nanophotonic resonators are central to numerous applications, from efficient spin-photon interfaces to laser oscillators and precision sensing. A leading approach consists of photonic crystal (PhC) cavities, which have been realized in a…