Related papers: Progress of Diamond Digital Low Level RF
A new generation of storage ring-based light source, called diffraction-limited storage ring (DLSR), with emittance approaching the diffraction limit for multi-keV photons by means of multi-bend achromat lattice, has attracted worldwide and…
The damped and sub-damped Lyman alpha systems (DLAs and sub-DLAs) traced in absorption against bright background quasars represent the main reserve of neutral hydrogen at high redshifts. We used the archival Very Large Telescope (VLT)…
Employing low-resolution analog-to-digital converters (ADCs) for millimeter wave receivers with large antenna arrays provides opportunity to efficiently reduce power consumption of the receiver. Reducing ADC resolution, however, results in…
LCLS-II is currently in its commissioning phase at SLAC. It is an X-ray FEL driven by a CW superconducting LINAC. The beam injector plays a crucial role in the overall performance of the accelerator, and is critical to the final electron…
We present the second prototype of a time-to-digital (TDC) ASIC for the upgrade of the ATLAS Monitored Drift Tube (MDT) detector for High-Luminosity LHC operations. Compared to the first prototype, triple modular redundancy has been…
The aim of this work is to test the capacity of a low cost but powerful device to be used in gamma spectrometry. The IZIRUNF0 [1] is an embedded STM32 board device with an ARM Cortex-M0 microcontroller build in. The possibilities offered by…
A 20 GHz LLRF system is being built using a two-board(RF Front End + ADC/DAC/FPGA) architecture. The RF Front End provides 8 down-converting channels and 3 up-converting channels (5.5-20 GHz RF to 0.05-3 GHz IF). Separate, phase locked,…
We experimentally study the transport properties of silicon quantum dots (QDs) fabricated from a highly doped n-type silicon-on-insulator wafer. Low noise electrical measurements using a low temperature complementary…
At Diamond Light Source, the UK's national synchrotron facility, electron beam disturbances are attenuated by the fast orbit feedback (FOFB), which controls a cross-directional (CD) system with hundreds of inputs and outputs. Due to the…
Integrated Sensing and Communication (ISAC) has attracted substantial attraction in recent years for spectral efficiency improvement, enabling hardware and spectrum sharing for simultaneous sensing and signaling operations. In-band Full…
We report on the design, implementation and characterization of fully digital control loops for laser frequency stabilization, differential phase-locking and performance optimization of the optical metrology system on-board the LISA…
In the R&D of the CSNS Drift Tube Linac (DTL), the first unit tank with 28 drift tubes has been developed. The axial accelerating field is ramped from 2.2MV/m to 3.1MV/m in this tank. The required field flatness is less than 2 % with the…
It is foreseen to significantly increase the luminosity of the LHC in order to harvest the maximum physics potential. Especially the Phase-II-Upgrade foreseen for 2023 will mean unprecedented radiation levels, significantly beyond the…
The purpose was two-fold: To explore the capability of the Diamond Synchrotron infra-red so as to include near-field photothermal microspectroscopy (PTMS); and Toward a quantitative nanohistology - investigation of scleroderma using…
In this paper we revisit hybrid analog-digital precoding systems with emphasis on their modelling and radio-frequency (RF) losses, to realistically evaluate their benefits in 5G system implementations. For this, we decompose the analog…
The Proof-of-Principle (POP) prototype of the Rf-Focused Drift tube (RFD) linac structure is currently under test at Linac Systems, after years of delay due to a variety of technical problems. A discussion of these technical problems and…
To meet the increasing requirements of synchrotron radiation users, the upgrade project to enhance the performance of Hefei Light Source (HLS), named HLS-II, was launched in 2010, and in 2014 the first commissioning of HLS-II was…
Additive manufacturing is a versatile technique that shows promise in providing quick and dynamic manufacturing for complex engineering problems. Research has been ongoing into the use of additive manufacturing for potential applications in…
We report the design and construction of a novel soft x-ray diffractometer installed at Diamond Light Source. The beamline endstation RASOR is constructed for general users and designed primarily for the study of single crystal diffraction…
Artificially-grown diamond crystals have unique properties that make them suitable as solid-state particle detectors and dosimeters in high-radiation environments. We have been using sensors based on single-crystal diamond grown by chemical…