Related papers: Necessary and sufficient condition for a generic 3…
This article synthezises the most important results on the kinematics of cuspidal manipulators i.e. nonredundant manipulators that can change posture without meeting a singularity. The characteristic surfaces, the uniqueness domains and the…
This chapter is dedicated to the so-called cuspidal robots, i.e. those robots that can move from one inverse geometric solution to another without meeting a singular confuguration. This feature was discovered quite recently and has then…
Cuspidal robots can move from one inverse or direct kinematic solution to another without ever passing through a singularity. These robots have remained unknown because almost all industrial robots do not have this feature. However, in…
The workspace topologies of a family of 3-revolute (3R) positioning manipulators are enumerated. The workspace is characterized in a half-cross section by the singular curves. The workspace topology is defined by the number of cusps that…
Cuspidal robots are robots with at least two inverse kinematic solutions that can be connected by a singularity-free path. Deciding the cuspidality of generic 3R robots has been studied in the past, but extending the study to…
The aim of this paper is to classify one family of 3R serial positioning manipulators. This categorization is based on the number of cusp points of quaternary, binary, generic and non-generic manipulators. It was found three subsets of…
Having non-singular assembly modes changing trajectories for the 3-RPS parallel robot is a well-known feature. The only known solution for defining such trajectory is to encircle a cusp point in the joint space. In this paper, the aspects…
This paper investigates the cuspidal configurations of 3-RPR parallel manipulators that may appear on their singular surfaces in the joint space. Cusp points play an important role in the kinematic behavior of parallel manipulators since…
A cuspidal robot can move from one inverse kinematics (IK) solution to another without crossing a singularity. Multiple industrial robots are cuspidal. They tend to have a beautiful mechanical design, but they pose path planning challenges.…
This paper demonstrates that any general 3-DOF three-legged planar parallel robot with extensible legs can change assembly modes without passing through parallel singularities (configurations where the mobile platform loses its stiffness).…
This paper investigates the conditions in the design parameter space for the existence and distribution of the cusp locus for planar parallel manipulators. Cusp points make possible non-singular assembly-mode changing motion, which…
This paper presents the kinematic analysis of the 3-PPPS parallel robot with an equilateral mobile platform and a U-shape base. The proposed design and appropriate selection of parameters allow to formulate simpler direct and inverse…
We present a theoretical and numerical analysis of the kinematics for the "Transpressor", a cuspidal 6R robot. It admits up to 16 inverse kinematics solutions which are described geometrically. For special target poses, we provide the…
This paper investigates the existence conditions of cusp points in the design parameter space of the R\underline{P}R-2P\underline{R}R parallel manipulators. Cusp points make possible non-singular assembly-mode changing motion, which can…
A family of reconfigurable parallel robots can change motion modes by passing through constraint singularities by locking and releasing some passive joints of the robot. This paper is about the kinematics, the workspace and singularity…
This paper presents an algorithm for detecting and computing the cusp points in the joint space of 3-RPR planar parallel manipulators. In manipulator kinematics, cusp points are special points, which appear on the singular curves of the…
In field environments, numerous robots necessitate manual intervention for restoration of functionality post a turnover, resulting in diminished operational efficiency. This study presents an innovative design solution for a reversible…
This paper proposes a new design method to determine the feasible set of parameters of translational or position/orientation decoupled parallel robots for a prescribed singularity-free workspace of regular shape. The suggested method uses…
Positioning 3R manipulators may have two or four inverse kinematic solutions (IKS). This paper derives a necessary and sufficient condition for 3R positioning manipulators with orthogonal joint axes to have four distinct IKS. We show that…
This article presents a new variable actuation mechanism based on the 3-RPR parallel robot. This mechanismis an evolution of the NaVARo robot, a 3-RRR parallel robot, for which the second revolute joint of the threelegs is replaced by a…