Related papers: Geometric Stochastic Filter with Guaranteed Perfor…
Visual and lidar Simultaneous Localization and Mapping (SLAM) algorithms benefit from the Inertial Measurement Unit (IMU) modality. The high-rate inertial data complement the other lower-rate modalities. Moreover, in the absence of constant…
This paper presents a novel framework for estimating the position and orientation of flexible manipulators undergoing vertical motion using multiple inertial measurement units (IMUs), optimized and calibrated with ground truth data. The…
Millimeter-wave radar provides robust perception in visually degraded environments. However, radar-inertial state estimation is inherently susceptible to drift. Because radar yields only sparse, body-frame velocity measurements, it provides…
Over the past decade, lidars have become a cornerstone of robotics state estimation and perception thanks to their ability to provide accurate geometric information about their surroundings in the form of 3D scans. Unfortunately, most of…
Accurately estimating vehicle velocity via smartphone is critical for mobile navigation and transportation. This paper introduces a cutting-edge framework for velocity estimation that incorporates temporal learning models, utilizing…
For reliable operation on urban roads, navigation using the Global Navigation Satellite System (GNSS) requires both accurately estimating the positioning detail from GNSS pseudorange measurements and determining when the estimated position…
Combining Global Navigation Satellite System (GNSS) with visual and inertial sensors can give smooth pose estimation without drifting. The fusion system gradually degrades to Visual-Inertial Odometry (VIO) with the number of satellites…
Pose estimation purely based on 3D point-cloud could suffer from degradation, e.g. scan blocks or scans in repetitive environments. To deal with this problem, we propose an approach for fusing 3D spinning LiDAR and IMU to estimate the…
The non-commutative nature of 3D rotations poses well-known challenges in generalizing planar problems to three-dimensional ones, even more so in contact-rich tasks where haptic information (i.e., forces/torques) is involved. In this sense,…
Inertial sensors based on micro-electromechanical systems (MEMS) technology, such as accelerometers and angular rate sensors, are cost-effective solutions used in inertial navigation systems in a broad spectrum of applications that estimate…
In this paper, we study state estimation of multi-visual-inertial systems (MVIS) and develop sensor fusion algorithms to optimally fuse an arbitrary number of asynchronous inertial measurement units (IMUs) or gyroscopes and global and(or)…
In various applications of land vehicle navigation and automatic guidance systems, Global Navigation Satellite System/Inertial Measurement Unit (GNSS/IMU) positioning performance crucially depends on the attitude determination accuracy…
This paper proposes a novel unit-quaternion observer-based controller for attitude tracking (attitude and angular velocity) with guaranteed transient and steady-state performance. The proposed approach is computationally cheap and can…
This paper presents a novel method for visual-inertial odometry. The method is based on an information fusion framework employing low-cost IMU sensors and the monocular camera in a standard smartphone. We formulate a sequential inference…
Inertial motion capture systems widely use low-cost IMUs to obtain the orientation of human body segments, but these sensors alone are unable to estimate link positions. Therefore, this research used a SLAM method in conjunction with…
Camera-IMU (Inertial Measurement Unit) sensor fusion has been extensively studied in recent decades. Numerous observability analysis and fusion schemes for motion estimation with self-calibration have been presented. However, it has been…
Accurate odometry is a critical component in a robotic navigation stack, and subsequent modules such as planning and control often rely on an estimate of the robot's motion. Sensor-based odometry approaches should be robust across sensor…
This paper addresses 6-DOF (degree-of-freedom) tactile localization, i.e. the pose estimation of tridimensional objects given tactile measurements. This estimation problem is fundamental for the operation of autonomous robots that are often…
The common approach to inertial sensor calibration for navigation purposes has been to model the stochastic error signals of individual sensors independently, whether as components of a single inertial measurement unit (IMU) in different…
Seamless operation of mobile robots in challenging environments requires low-latency local motion estimation (e.g., dynamic maneuvers) and accurate global localization (e.g., wayfinding). While most existing sensor-fusion approaches are…