Related papers: Liquid film dynamics with immobile contact line du…
In this work, we extend the model of contact angles that we have previously developed for sessile drops on a wetted surface to the case of a meniscus in a capillary. The underlying physics of our model describe the intermolecular forces…
Fluid exchange between a soap film and its bounding menisci governs film drainage and stability, with direct implications for the lifetime of surface bubbles and liquid foams. Despite recent advances, a quantitative characterization of this…
In recent years, slippery surfaces have attracted significant interest due to their excellent liquid-repellent properties and their potential in diverse commercial applications. Such surfaces are prepared by coating functionalized solid…
We account for the presence of surface charges towards describing variations in the dynamic contact angle of an advancing liquid-gas meniscus. Starting from the thin-film based formalism, we present closed-form analytical expressions…
In this paper, we discuss a particular model arising from sinking of a rigid solid into a thin film of fluid, i.e. a fluid contained between two solid surfaces and part of the fluid surface is in contact with the air. The fluid is governed…
When a suspension dries, the suspending fluid evaporates, leaving behind a dry film composed of the suspended particles. During the final stages of drying, the height of the fluid film on the substrate drops below the particle size,…
We consider the unsteady thin-film dynamics of a long bubble of negligible viscosity that advances at a uniform speed in a cylindrical capillary tube. The bubble displaces a viscous, nonwetting fluid, creating a thin film between its…
Liquid foams exhibit menisci whose lengths range from hundreds of microns in microfoams to several centimeters in macroscopic bubble arrangements. These menisci thin under gravity until reaching a steady thickness profile, where hydrostatic…
We investigate experimentally the receding of a contact line when a Peltier module is pulled out of a water bath at constant speed, while a ice layer is also growing at constant speed on the Peltier module. A steady regime is therefore…
Drying suspensions often leave behind complex patterns of particulates, as might be seen in the coffee stains on a table. Here we consider the dynamics of periodic band or uniform solid film formation on a vertical plate suspended partially…
In part 1, we proposed a model of dynamics of wetting for slow movements near a contact line formed at the interface of two immiscible fluids and a solid when viscous dissipation remains bounded. The contact line is not a material line and…
The aim of this study is to derive accurate models for quantities characterizing the dynamics of droplets of non-vanishing viscosity in capillaries. In particular, we propose models for the uniform-film thickness separating the droplet from…
Many microfluidics devices, coating processes or diphasic flows involve the motion of a liquid meniscus on a wet wall. This motion induces a specific viscous force, that exhibits a non-linear dependency in the meniscus velocity. We propose…
Molecular dynamics simulations are used to study the capillary adhesion from a nonvolatile liquid meniscus between a spherical tip and a flat substrate. The atomic structure of the tip, the tip radius, the contact angles of the liquid on…
The present study reports a novel physical model for simulating Pulsating Heat Pipes (PHP). Their high heat performance is due to the phase change over thin liquid films. The simulation of physically correct film behavior is thus crucial.…
We study the forced displacement of a fluid-fluid interface in a three-dimensional channel formed by two parallel solid plates. Using a Lattice-Boltzmann method, we study situations in which a slip velocity arises from diffusion effects…
The flow near a moving contact line depends on the dynamic contact angle, viscosity ratio, and capillary number. We report experiments involving immersing a plate into a liquid bath, concurrently measuring the interface shape, interfacial…
In recent years, there has been a considerable interest in the mechanics of soft objects meeting fluid interfaces (elasto-capillary interactions). In this work we experimentally examine the case of a fluid resting on a thin film of rigid…
A moving contact line occurs at the intersection of an interface formed between two immiscible liquids and a solid. According to viscous theory, the flow is entirely governed by just two parameters, the viscosity ratio, $\lambda$, and the…
The highly confined flow of the liquid phase, trapped between the gas bubbles, is at the origin of the large effective viscosity of the liquid foams. Despite the industrial relevance of this complex fluid, the foam viscosity remains…