Related papers: Stability enhancement of ITO-free non-inverted PTB…

We have performed resistivity measurements of poly[3,4-ethylenedioxythiophene]: poly[styrenesulfonate] (PEDOT:PSS) films with varying concentrations of glycerol. Resistivity is seen to decrease exponentially from roughly 3 ohm-cm for pure…

In terms of mixing graded TiO2 and SnO2 powders by solid-state reaction method, ITO was prepared. Using electron beam gun technology, ITO films with different thicknesses were prepared. The influence of film thickness on structure,…

"Secondary doping" in poly(3,4-ethylenedioxy-thiophene):poly(styrenesulfonate) (PEDOT:PSS) is quite effective and a frequently used method for the conductivity enhancement. This simple approach, the addition of co-solvents to the PEDOT:PSS…

Previous studies of reverse-bias stability in perovskite solar cells have focused primarily on voltage controlled reverse-bias tests. Here we instead present an investigation of perovskite solar cell degradation under well-defined, constant…

Organic solar cells (OSCs) containing an active layer consisting of a nanostructured blend of a conjugated polymer like poly(3-hexylthiophene) (P3HT) and an electron acceptor molecule have the potential of competing against silicon-based…

Si doped ZnO has been reported to be a better conductor than pure ZnO. It is reported that carrier density increases and hence conductivity increases. However, the effect on optical transmission is yet not clear until our recent report [1].…

Durable delustered PET (PET-TiO2) fabrics super hydrophilic surface has been obtained by plasma selecting etching. The aging effect of their hydrophilicity after plasma treatment has been investigated with storage time. After Ar/O2 radio…

Inorganic cesium lead iodide (CsPbI$_3$) perovskite solar cells (PSCs) have attracted enormous attention due to their excellent thermal stability and optical bandgap (~1.73 eV), well-suited for tandem device applications. However, achieving…

Poly(3,4-ethylenedioxythiophene):polystyrenesulfonate (PEDOT:PSS) has been widely used as a hole transport layer in perovskite solar cells (PSCs). However, the high interface defect density and energy level mismatch between PEDOT:PSS and…

Poly(ethylene terephthalate) (PET) films are widely used in flexible electronics and optoelectronics, where their mechanical durability and optical performance under strain are essential for device reliability. This study investigates the…

Thin-film solar cells suffer from various types of recombination, of which leakage current usually dominates at lower voltages. Herein, we demonstrate first a three-order reduction of the shunt loss mechanism in planar methylammonium lead…

After the efficiency of organic photovoltaic (OPV) cells achieved more than 10%, the control of stability and degradation mechanisms of solar cells became a prominent task. The improvement of device efficiency due to incorporation of a…

A lead-free, completely inorganic, and non-toxic Cs2TiBr6-based double perovskite solar cell (PSC) was simulated via SCAPS 1-D. La-doped BaSnO3 (LBSO) was applied as the electron transport layer (ETL) unprecedentedly in the simulation study…

We provide direct evidence of the effects of interface engineering of various substrates by Microbubble lithography (MBL). We choose a model organic plastic (or polymer) poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS),…

Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is widely used to build optoelectronic devices. However, as a hygroscopic water-based acidic material, it brings major concerns for stability and degradation, resulting in…

Poly(3,4-ethylenedioxythiophene) : poly(styrene sulfonic acid (PEDOT:PSS), an optically transparent organic semi-conductor, constitutes a suspension of conducting PEDOT:PSS grains, shelled by an insulating layer of PSS. While a percolation…

The stability of perovskite solar cells is closely related to the defects in perovskite crystals, and there are a large number of crystal defects in the perovskite thin films prepared by the solution method, which is not conducive to the…

Halide perovskite solar cells (PSCs) offer high efficiency and low costs, making them key for future photovoltaics. Optimizing charge transport layers is crucial, with porous TiO$_2$ widely used as electron transport layers (ETL) due to its…

It is demonstrated that persistent-photoconductivity (PPC), well-studied in lightly-doped semiconductors, is observable in GeSbTe compounds using infrared excitation at cryogenic temperatures. The low level of energy-flux necessary to…

The development of scalable 1.25 eV mixed Pb-Sn perovskite solar modules by blade coating lags behind Pb-based perovskites due to limited understanding of solution-substrate interaction of the perovskite ink on PEDOT:PSS and subsequent gas…