Related papers: Soft-Elasticity Optimises Dissipation in 3D-Printe…
Hydrodynamic collapse of a central air-cavity during the recoil phase of droplet impact on a superhydrophobic sieve leads to satellite-free generation of a single droplet through the sieve. Two modes of cavity formation and droplet ejection…
Superconductivity in the two-dimensional (2D) limit is a fertile ground for exotic quantum phenomena-many of which remain elusive in their 3D counterparts. While studies of 2D superconductivity have predominantly focused on mono- or…
In-situ white light Laue diffraction has been successfully used to interrogate the structure of single crystal materials undergoing rapid (nanosecond) dynamic compression up to megabar pressures. However, information on strain state…
Models of smectic-C liquid crystal elastomers predict that it can display soft elasticity, in which the shape of the elastomer changes at no energy cost. The amplitude of the soft mode and the accompanying shears are dependent on the…
Embedding magnetic colloidal particles in an elastic polymer matrix leads to smart soft materials that can reversibly be addressed from outside by external magnetic fields. We discover a pronounced nonlinear superelastic stress-strain…
Soft substrates such as polydimethylsiloxane (PDMS) enhance droplet nucleation during the condensation of water vapour, because their deformability inherently reduces the energetic threshold for heterogeneous nucleation relative to rigid…
The mechanical properties of liquid crystal elastomers (LCEs) make them suitable candidates for pressure-sensitive adhesives (PSAs). Using the nematic dumbbell constitutive model, and the block model of PSAs, we study their tack energy and…
Solids deform and fluids flow, but soft glassy materials, such as emulsions, foams, suspensions, and pastes, exhibit an intricate mix of solid and liquid-like behavior. While much progress has been made to understand their elastic (small…
Soft pair potentials predict a reentrant liquid phase for high concentrations, a behavior not observed experimentally. Here, very soft microgels confined at an oil-water interface are used as a model system of particles interacting via a…
Silicene, a two-dimensional (2D) allotrope of silicon, has attracted significant interest for its electronic and mechanical properties, alongside its compatibility with various substrates. In this study, we investigate the structural and…
Liquid crystal elastomer films that morph into cones are strikingly capable lifters. Thus motivated, we combine theory, numerics, and experiments to reexamine the load-bearing capacity of conical shells. We show that a cone squashed between…
We propose a 3D-printed graded lattice made of hollow elliptical cylinders (HECs) as a new way to design impact mitigation systems. We observe asymmetric dynamics in the graded HEC chains with increasing and decreasing stiffness.…
With a novel 3D discrete-element method specially developed with adhesive contact mechanics, random loose packings of uniform spherical micron-sized particles are fully investigated. The results show that large velocity, large size or weak…
Piezoelectricity, the generation of electric charge in response to mechanical stress, is a key property in both natural and synthetic materials. This study significantly boosts the piezoelectric response of chitosan, a biodegradable…
Elastocaloric cooling has been identified as a promising alternative to high global warming potential vapor compression cooling. Two key bottlenecks to adoption are the need for bulky/expensive actuators to provide sufficient uniaxial…
We study the lubrication of fluid-immersed soft interfaces and show that elastic deformation couples tangential and normal forces and thus generates lift. We consider materials that deform easily, due to either geometry (e.g. a shell) or…
Energy absorbing materials, like foams used in protective equipment, are able to undergo large deformations under low stresses, reducing the incoming stress wave below an injury or damage threshold. They are typically effective in absorbing…
Electroplasticity is defined as the reduction in flow stress of a material undergoing deformation on passing an electrical pulse through it. The lowering of flow stress during electrical pulsing has been attributed to a combination of three…
Fluid-driven elastomeric actuators (FEAs) are among the most popular actuators in the emerging field of soft robotics. Intrinsically compliant, with continuum of motion, large strokes, little friction, and high power-to-weight ratio, they…
Strain engineering is a powerful tool for tuning the electronic, magnetic, and topological properties of two-dimensional (2D) materials and thin films - particularly at high values of strain (>3%) where many electronic, magnetic, and…