Related papers: End-Effector Stabilization of a 10-DOF Mobile Mani…
We consider a nonprehensile manipulation task in which a mobile manipulator must balance objects on its end effector without grasping them -- known as the waiter's problem -- and move to a desired location while avoiding static and dynamic…
This paper proposes a new nonlinear stability analysis for the acceleration-based robust position control of robot manipulators by using Disturbance Observer (DOb). It is shown that if the nominal inertia matrix is properly tuned in the…
Multi-degree-of-freedom (DOF) robotic manipulators exhibit strongly nonlinear, high-dimensional, and coupled dynamics, posing significant challenges for controller design. To address these issues, this work proposes a unified hybrid control…
Designing a model predictive control (MPC) scheme that enables a mobile robot to safely navigate through an obstacle-filled environment is a complicated yet essential task in robotics. In this technical report, safety refers to ensuring…
The autonomous operation of tracked mobile manipulators in rescue missions requires not only ensuring the reachability and safety of robot motion but also maintaining stable end-effector manipulation under diverse task demands. However,…
Human beings can utilize multiple balance strategies, e.g. step location adjustment and angular momentum adaptation, to maintain balance when walking under dynamic disturbances. In this work, we propose a novel Nonlinear Model Predictive…
The precise motion control of a multi-degree of freedom~(DOF) robot manipulator is always challenging due to its nonlinear dynamics, disturbances, and uncertainties. Because most manipulators are controlled by digital signals, a novel…
As off-the-shelf (OTS) autopilots become more widely available and user-friendly and the drone market expands, safer, more efficient, and more complex motion planning and control will become necessary for fixed-wing aerial robotic…
Tendon-Driven Continuum Robots (TDCRs) have the potential to be used in minimally invasive surgery and industrial inspection, where the robot must enter narrow and confined spaces. We propose a Model Predictive Control (MPC) approach to…
Non-linear model predictive control (nMPC) is a powerful approach to control complex robots (such as humanoids, quadrupeds, or unmanned aerial manipulators (UAMs)) as it brings important advantages over other existing techniques. The…
This paper presents a stochastic/robust nonlinear model predictive control (NMPC) to enhance the robustness of model-based legged locomotion against contact uncertainties. We integrate the contact uncertainties into the covariance…
This paper presents a new task-space Non-singular Terminal Super-Twisting Sliding Mode (NT-STSM) controller with adaptive gains for robust trajectory tracking of a 7-DOF robotic manipulator. The proposed approach addresses the challenges of…
Nonlinear Model Predictive Control (NMPC) is a powerful and widely used technique for nonlinear dynamic process control under constraints. In NMPC, the state and control weights of the corresponding state and control costs are commonly…
Many day-to-day activities require the dexterous manipulation of a redundant humanoid arm in complex 3D environments. However, position regulation of such robot arm systems becomes very difficult in presence of non-linear uncertainties in…
For soft robots to work effectively in human-centered environments, they need to be able to estimate their state and external interactions based on (proprioceptive) sensors. Estimating disturbances allows a soft robot to perform desirable…
The use of exoskeleton robots is increasing due to the rising number of musculoskeletal injuries. However, their effectiveness depends heavily on the design of control systems. Designing robust controllers is challenging because of…
This article focuses on the trajectory tracking problem of mobile manipulators (MMs). Firstly, we construct a position and orientation model predictive tracking control (POMPTC) scheme for mobile manipulators. The proposed POMPTC scheme can…
The growing need to automate processes in industrial settings has led to tremendous growth in the robotic systems and especially the robotic arms. The paper assumes the design, modeling and control of a robotic arm to suit industrial…
This paper uses Model Predictive Control (MPC) to optimise the input torques of a Three-Degrees-of-Freedom (DOF) robotic arm, enabling it to operate to the target position and grasp the object accurately. A monocular camera is firstly used…
This study aims to design a motion/force controller for an aerial manipulator which guarantees the tracking of time-varying motion/force trajectories as well as the stability during the transition between free and contact motions. To this…