Related papers: Hybrid Interference Mitigation Using Analog Prewhi…
Millimeter wave (mmWave) massive MIMO can achieve orders of magnitude increase in spectral and energy efficiency, and it usually exploits the hybrid analog and digital precoding to overcome the serious signal attenuation induced by mmWave…
Strong self-interference due to the co-located transmitter is the bottleneck for implementing an in-band full-duplex (IBFD) system. If not adequately mitigated, the strong interference can saturate the receiver's analog-digital converters…
Low-resolution analog-to-digital converters (ADCs) simplify the design of millimeter-wave (mmWave) massive multi-user multiple-input multiple-output (MU-MIMO) basestations, but increase vulnerability to jamming attacks. As a remedy, we…
The potential of deploying large-scale antenna arrays in future wireless systems has stimulated extensive research on hybrid transceiver designs aiming to approximate the optimal fully-digital schemes with much reduced hardware cost and…
Millimeter-wave (mmWave) technology is one of the most promising candidates for future wireless communication systems as it can offer large underutilized bandwidths and eases the implementation of large antenna arrays which are required to…
Hybrid analog-digital precoding significantly reduces the hardware costs in massive MIMO transceivers when compared to fully-digital precoding at the expense of increased transmit power. In order to mitigate the above shortfall, we use the…
Milimeter wave (mmWave) band mobile communications can be a solution to the continuously increasing traffic demand in modern wireless systems. Even though mmWave bands are scarcely occupied, the design of a prospect transceiver should…
Hybrid precoding is a promising technique for mmWave massive MIMO systems, as it can considerably reduce the number of required radio-frequency (RF) chains without obvious performance loss. However, most of the existing hybrid precoding…
Millimeter wave (mmWave) MIMO will likely use hybrid analog and digital precoding, which uses a small number of RF chains to avoid energy consumption associated with mixed signal components like analog-to-digital components not to mention…
In massive MIMO systems, hybrid beamforming is an essential technique for exploiting the potential array gain without using a dedicated RF chain for each antenna. In this work, we consider the data phase in a massive MIMO communication…
In modern wireless networks, interference is no longer negligible since each cell becomes smaller to support high throughput. The reduced size of each cell forces to install many cells, and consequently causes to increase inter-cell…
Wireless systems with inband full-duplex transceiver typically require multiple lines of defense against the effect of harsh self-interference, specifically, to avoid saturation of the analog-to-digital converter (ADC) in the receiver. We…
Hybrid precoding is a cost-effective approach to support directional transmissions for millimeter wave (mmWave) communications. While existing works on hybrid precoding mainly focus on single-user single-carrier transmission, in practice…
Hybrid precoding is an indispensable technique to harness the full potential of a multi-user massive multiple-input, multiple-output (MU-MMIMO) system. In this paper, we propose a new hybrid precoding approach that combines digital and…
Medium-scale or large-scale receive antenna array with digital beamforming can be employed at receiver to make a significant interference reduction, but leads to expensive cost and high complexity of the RF-chain circuit. To deal with this…
Hybrid precoding has been recently proposed as a cost-effective transceiver solution for millimeter wave (mm-wave) systems. While the number of radio frequency (RF) chains has been effectively reduced in existing works, a large number of…
Millimeter wave (mmWave) systems will likely employ large antenna arrays at both the transmitters and receivers. A natural application of antenna arrays is simultaneous transmission to multiple users, which requires multi-user precoding at…
As a key enabling technology for 5G wireless, millimeter wave (mmWave) communication motivates the utilization of large-scale antenna arrays for achieving highly directional beamforming. However, the high cost and power consumption of RF…
A network relying on a large antenna-array-aided base station is designed for delivering multiple information streams to multi-antenna users over high-frequency bands such as the millimeter-wave and sub-Terahertz bands. The state-of-the-art…
Hybrid analog/digital precoding in millimeter-wave (mmWave) multi-input multi-ouput (MIMO) systems is capable of achieving the near-optimal full-digital performance at reduced hardware cost and power consumption compared to its full-RF…