Related papers: Near-Field Linear Sampling Method forAxisymmetric …
Being able to quantify the corrosion of ferromagnetic water pipeline is a critical task for avoiding pipe failures. This task is often performed with Non-Destructive Evaluation (NDE) technologies and solving the inverse modeling of the…
In electromagnetic analysis, the finite element and boundary element methods jointly known as 'FEM-BEM coupling' is applied for numerically solving levitation problem based on eddy current. The main focus behind this coupled analysis method…
Low-energy electron microscopy (LEEM) is a surface science method that works primarily in the UHV environment. It provides information complementary to the other established techniques: it extends the limited view of scanning probe…
A new methodology for the improvement of the performance of inexpensive static passive electromagnetic skins (SP-EMSs) is presented. The proposed approach leverages on the non-uniqueness of the inverse source problem associated to the…
The three scanning electron microscope diffraction based techniques of electron channelling patterns (ECPs), electron channelling contrast imaging (ECCI), and electron back scatter diffraction (EBSD) are reviewed. The dynamical diffraction…
Serial section electron microscopy (ssEM) is a widely used technique for obtaining volumetric information of biological tissues at nanometer scale. However, accurate 3D reconstructions of identified cellular structures and volumetric…
In this paper, we propose a variational approach to estimate eddy viscosity using forward sensitivity method (FSM) for closure modeling in nonlinear reduced order models. FSM is a data assimilation technique that blends model's predictions…
Axisymmetric free-boundary equilibrium reconstructions of tokamak plasmas in the Lithium Tokamak eXperiment (LTX) are performed using the PSI-Tri equilibrium code. Reconstructions in LTX are complicated by the presence of long-lived…
This paper presents a new acoustic emission (AE) source localization for isotropic plates with reflecting boundaries. This approach that has no blind spot leverages multimodal edge reflections to identify AE sources with only a single…
An electrohydrodynamic numerical model is used to explore the electrospray emission behavior of both moderate and high electrical conductivity liquids under electrospray conditions. The Volume-of-Fluid method, incorporating a…
The transient response from a transmitter-receiver coil system inside a multi-layer cylindrical conductive configuration is obtained. The particular set-up applies to well logging as well as to eddy current tube testing. In this work, a…
Scanning transmission electron microscopy (STEM) has advanced rapidly in the last decade thanks to the ability to correct the major aberrations of the probe forming lens. Now atomic-sized beams are routine, even at accelerating voltages as…
Electrometry near a dielectric surface is performed using Rydberg electromagnetically induced transparency (EIT). The large polarizability of high n-state Rydberg atoms gives this method extreme sensitivity. We show that adsorbates on the…
Scanning Electron Microscopy (SEM) experiments provide detailed insights into material microstructures, enabling high-resolution imaging as well as crystallographic analysis through advanced techniques like Electron Backscatter Diffraction…
The NL-$e$EDM experiment searches for a non-zero electric dipole moment of the electron $d_e$ ($e$EDM) in the ground state of barium monofluoride (BaF). A beam of BaF from a supersonic expansion source is probed with the spin precession…
The Electrical Resistance Tomography (ERT) technique is applied to the measurement of sheet conductance maps of both uniform and patterned conductive thin films. Images of the sheet conductance spatial distribution, and local conductivity…
Measurements of the electron's electric dipole moment (eEDM) are demanding tests of physics beyond the Standard Model. We describe how ultracold YbF molecules could be used to improve the precision of eEDM measurements by two to three…
Electrochemical strains are a ubiquitous feature of solid state ionic devices ranging from ion batteries and fuel cells to electroresistive and memristive memories. Recently, we proposed a scanning probe microscopy (SPM) based approach,…
Momentum resolved 4D-STEM, also called center of mass (CoM) analysis, has been used to measure the long range built-in electric field of a silicon p-n junction. The effect of different STEM modes and the trade-off between spatial resolution…
Real-time monitoring of carbon fibre composites during Automated Fibre Placement (AFP) manufacturing remains a challenge for non-destructive evaluation (NDE) techniques. An directional eddy-current (EC) probe with asymmetric transmit and…