Related papers: Influence of Furnace Baking on Q-E Behavior of Sup…
The Medium temperature (mid-T) baking of niobium superconducting radio-frequency cavities at 300 350  C in a vacuum furnace is known to enhance the quality factor (Q₀). However, despite this improvement, cavities treated with…
Medium temperature (mid-T) baking, typically conducted at 300 350 C, enhances the quality factor of niobium (Nb) superconducting radio frequency cavities. High vacuum furnace baking is commonly preferred for its practicality in large-scale…
Vacuum thermal treatments (baking) are known to improve the superconducting properties of the RF surface layer of niobium cavities, and are employed as a last processing step to increase their efficiency determined by intrinsic quality…
We report the rf performance of a single-cell superconducting radiofrequency cavity after low temperature baking in a nitrogen environment. A significant increase in quality factor has been observed when the cavity was heat treated in the…
Recently, heat treatment between 250 C and 500 C has been attempted to improve quality factor of superconducting radio-frequency cavities at FNAL and KEK. Experiments of such medium temperature (mid-T) bake with furnaces have also been…
Nitrogen-doping and furnace-baking are advanced high-Q0 recipes developed for 1.3 GHz TESLA-type cavities. These treatments will significantly benefit the high-Q0 linear accelerator community if they can be successfully adapted to different…
We investigate the effect of high temperature treatments followed by only high-pressure water rinse (HPR) of superconducting radio frequency (SRF) niobium cavities. The objective is to provide a cost effective alternative to the typical…
We applied heat treatments to 80.5 MHz quarter-wave resonators made from bulk niobium and prepared with buffered chemical polishing BCP. We evaluated their performance at 4.3 K. We found that a 48 hour, 120 C bake-out ("low-temperature bake…
Most of the current research in superconducting radio frequency (SRF) cavities is focused on ways to reduce the construction and operating cost of SRF based accelerators as well as on the development of new or improved cavity processing…
Large-grain Nb has become a viable alternative to fine-grain Nb for the fabrication of superconducting radio-frequency cavities. In this contribution we report the results from a heat treatment study of a large-grain 1.5 GHz single-cell…
The improvement of the quality factor Q0 of superconducting radio-frequency (SRF) cavities at medium accelerating gradients (20-25 MV/m) is important in order to reduce the cryogenic losses in continuous wave (CW) accelerators used for a…
We report the RF performance of several single-cell superconducting radio-frequency cavities subjected to low temperature heat treatment in nitrogen environment. The cavities were treated at temperature 120 - 165 $^{\circ}$C for an extended…
Mid-T heat treatments in the range from 250 to 400 C on superconducting radio-frequency (SRF) cavities have been shown to provide high quality factors that rise with applied rf field strength in high frequency, electro-polished (EP),…
Under-vacuum low- and mid-temperature baking revealed beneficial effects on the performance of niobium-made cavities for superconducting radio-frequency (SRF) applications, primarily seen in particle accelerators. Such a baking process is…
For many new accelerator applications, superconducting radio frequency (SRF) systems are the enabling technology. In particular for CW applications, much effort is being expended to minimize the power dissipation (surface resistance) of…
This comprehensive study, being part of the European XFEL R\&D effort, elucidates the influence of medium temperature (mid-T) heat treatments between 250{\deg}C and 350{\deg}C on the performance of 1.3~GHz superconducting radiofrequency…
Recent advancement in superconducting radio frequency cavity processing techniques, with diffusion of impurities within the RF penetration depth, resulted in high quality factor with increase in quality factor with increasing accelerating…
An increase in the quality factor of superconducting radiofrequency cavities is achieved by minimizing the surface resistance during processing steps. The surface resistance is the sum of temperature independent residual resistance and…
The application of heat treatments on 1.3 GHz TESLA type cavities in ultra-high vacuum at 250{\deg}C to 350{\deg}C is called medium temperature or mid-T heat treatment. In various laboratories such treatments on superconducting radio…
Even when cooled through its transition temperature in the presence of an external magnetic field, a superconductor can expel nearly all external magnetic flux. This Letter presents an experimental study to identify the parameters that most…