Related papers: Determination of Calibration Parameters of Cantile…
A common use for atomic force microscopy is to quantify local forces through tip-sample interactions between the probe tip and a sample surface. The accuracy of these measurements depends on the accuracy to which the cantilever spring…
Atomic force microscopy (AFM) is a powerful tool to investigate interaction forces at the micro and nanoscale. Cantilever stiffness, dimensions and geometry of the tip can be chosen according to the requirements of the specific application,…
Quality factor plays a fundamental role in dynamic mode atomic force microscopy. We present a technique to modify the quality factor of an atomic force microscopy cantilever within a Fabry-P\'erot optical interferometer. The experimental…
A method is presented for calibrating the higher eigenmodes (resonance modes) of atomic force microscopy cantilevers that can be performed prior to any tip-sample interaction. The method leverages recent efforts in accurately calibrating…
The quantitative measurement of viscoelasticity of nano-scaleentities is an important goal of nanotechnology research and there is considerable progress with advent of dynamic Atomic Force Microscopy. The hydrodynamics of cantilever, the…
We present a theoretical framework for the dynamic calibration of the higher eigenmode parameters (stiffness and optical lever responsivity) of a cantilever. The method is based on the tip-surface force reconstruction technique and does not…
Non-invasive thermal noise calibration of both torsional and flexural eigenmodes is performed on numerous cantilevers of 10 different types. We show that for all tipless and short-tipped cantilevers, the ratio of torsional to flexural mode…
An ongoing challenge in atomic force microscope (AFM) experiments is the quantitative measurement of cantilever motion. The vast majority of AFMs use the optical beam deflection (OBD) method to infer the deflection of the cantilever. The…
Nowadays, silicon micro-cantilevers with different geometrical shapes are widely used as micro-electro-mechanical systems and, more recently, as force sensor probes in atomic force microscopy (AFM). During the last ten years, several…
Colloidal probes are often used in force microscopy when the geometry of the tip-sample interaction should be well controlled. Their calibration requires the understanding of their mechanical response, which is very sensitive to the details…
A method to precisely calibrate the oscillation amplitude in Dynamic Scanning Force Microscopy is described. It is experimentally shown that a typical electronics used to process the dynamic motion of the cantilever can be adjusted to…
High-frequency atomic force microscopy has enabled extraordinary new science through large bandwidth, high speed measurements of atomic and molecular structures. However, traditional optical detection schemes restrict the dimensions, and…
The torsional vibration of atomic force microscope (AFM) cantilevers is critical for high-sensitivity measurements, yet existing models for width-varying cantilevers often rely on approximations that lead to significant discrepancies with…
A spreadsheet algorithm is given for the atomic force microscope that accounts for non-linear behavior in the deflection of the cantilever and in the photo-diode response. In addition, the data analysis algorithm takes into account…
Experimental methods and procedures required for precision measurements of the Casimir force are presented. In particular, the best practices for obtaining stable cantilevers, calibration of the cantilever, correction of thermal and…
Measurements of the deflection induced by thermal noise have been performed on a rectangular atomic force microscope cantilever in air. The detection method, based on polarization interferometry, can achieve a resolution of 1E-14 m/rtHz in…
Atomic force microscopy (AFM) is an analytical surface characterization tool which can reveal a sample's topography with high spatial resolution while simultaneously probing tip-sample interactions. Local measurement of chemical properties…
A new method is introduced for calibrating lateral force as measured by an atomic force microscope (AFM), making use of both an interferometric detector and an optical beam detector on the same instrument. The method may be implemented…
The functionalization of an Atomic Force Microscope (AFM) cantilever with a colloidal bead is a widely used technique when the geometry between the probe and the sample must be controlled, particularly in force spectroscopy. But some…
Optical beam deflection is a popular method to measure the deformation of micromechanical devices. As it measures mostly a local slope, its sensitivity depends on the location and size of the optical spot. We present a method to evaluate…