Related papers: Two comments on adhesion
The temperature increase in the contact regions between solids in sliding contact has a huge influence on friction and wear. Here we test an analytical theory for the flash temperature, valid for randomly rough surface with multiscale…
When a fluid surface adheres to a substrate, the location of the contact line adjusts in order to minimize the overall energy. This adhesion balance implies boundary conditions which depend on the characteristic surface deformation…
We study the interaction of two parallel rigid cylinders on the surface of a thin elastic film supported on a pool of liquid. The excess energy of the surface due to the curvature of the stretched film induces attraction of the cylinders…
In this study, the adhesion-detachment behaviour of a gecko-inspired adhesive pad was investigated to understand the on/off switching mechanisms of adhesion in gecko feet. A macroscopic spatula model was fabricated using silicone rubber,…
The jamming transition, generally manifested by a rapid increase of rigidity under compression (i.e., compression hardening), is ubiquitous in amorphous materials. Here we study shear hardening in deeply annealed frictionless packings…
Friction is usually a very complicated process. It appears in its most elementary form when two flat surfaces separated by vacuum gap are sliding relative to each other at zero Kelvin and the friction is generated by the relative movement…
We present a novel theory of the adhesive contact of linear viscoelastic materials against rigid substrates moving at constant velocity. Despite the non-conservative behavior of the system, the closure equation of the contact problem can be…
Most natural and man-made surfaces appear to be rough on many length scales. There is presently no unifying theory of the origin of roughness or the self-affine nature of surface topography. One likely contributor to the formation of…
The glass transition can simply be viewed as the point at which the viscosity of a structurally disordered liquid reaches 10^{13} Poise [1]. This definition is operational but it sidesteps fundamental controversies about the glass: Is the…
We compare rigidity of materials in two phases, liquid and solid phases. As a measure of the rigidity, we employ the one characterizing how firmly the material is fixed by low density of pinning centers, such as impurities and rough…
Cell-cell contacts in tissues are continuously subject to mechanical forces due to homeostatic pressure and active cytoskeleton dynamics. While much is known about the molecular pathways of adhesion, the role of mechanics is less well…
Two surfaces are "sticky" if breaking their mutual contact requires a finite tensile force. At low fractal dimensions D, there is consensus stickiness does not depend on the upper truncation frequency of roughness spectrum (or…
Liquids flow, making them remarkably distinct from solids and close to gases. At the same time, interactions in liquids are strong as in solids. The combination of these two properties is believed to be the ultimate obstacle to constructing…
We reported a phenomenon that when exerting an electric field gradient across a liquid metal/electrolyte interface, a droplet of the same liquid metal can persistently surf on the interface without coalescence. A thin layer of the…
When a droplet gently lands on an atomically smooth substrate, it will most likely contact the underlying surface in about 0.1 s. However, theoretical estimation from fluid mechanics predicts a contact time of 10 to 100 s. What causes this…
Though extensively studied, hardness, defined as the resistance of a material to deformation, still remains a challenging issue for a formal theoretical description due to its inherent mechanical complexity. The widely applied Teter's…
Blisters, delaminated regions that form in multilayered structures under compressive stresses, are observed across a wide range of length scales, from two-dimensional materials to protective coatings and laminated composites. Far from being…
Surface roughness emerges naturally during mechanical removal of material, fracture, chemical deposition, plastic deformation, indentation, and other processes. Here, we use continuum simulations to show how roughness which is neither…
We develop an analytical model of adhesive wear between two unlubricated rough surfaces, forming micro-contacts under normal load. The model is based on an energy balance and a crack initiation criteria. We apply the model to the problem of…
Wettability is the affinity of a liquid for a solid surface. For energetic reasons, macroscopic drops of liquid are nearly spherical away from interfaces with solids, and any local deformations due to molecular-scale surface interactions…