Related papers: Fundamental thermal noise limits for optical micro…
Current research on micro-mechanical resonators strives for quantum-limited detection of the motion of macroscopic objects. Prerequisite to this goal is the observation of measurement backaction consistent with quantum metrology limits.…
In force sensing, optomechanics, and quantum motion experiments, it is typically advantageous to create lightweight, compliant mechanical elements with the lowest possible force noise. Here we report wafer-scale batch fabrication and…
Systems with low mechanical dissipation are extensively used in precision measurements such as gravitational wave detection, atomic force microscopy and quantum control of mechanical oscillators via opto- and electromechanics. The…
High-stress Si$_3$N$_4$ nanoresonators have become an attractive choice for electro- and optomechanical devices. Membrane resonators can achieve quality factor ($Q$) - frequency ($f$) products exceeding $10^{13}$ Hz, enabling (in principle)…
We report a theoretical and experimental investigation of fiber Fabry-Perot cavities aimed at enhancing Kerr frequency comb generation. The modulation instability (MI) power threshold is derived from the linear stability analysis of a…
We show that fast technical fluctuations of microwave signals can be strongly suppressed by cryogenic resonators. The experiments were carried out with sapphire resonators cooled to approximately 6 K at frequencies around 11 GHz. Each…
Amplification is usually necessary when measuring the frequency instability of microwave signals. In this work, we develop a flicker noise free frequency measurement system based on a common or shared amplifier. First, we show that…
We use a transmon qubit and its dispersively coupled readout resonator to measure the Fock state populations of another microwave resonator, to which we have attached a quantum-circuit refrigerator (QCR). First, we apply noise generated at…
Macroscopic resonant tunneling between the two lowest lying states of a bistable RF-SQUID is used to characterize noise in a flux qubit. Measurements of the incoherent decay rate as a function of flux bias revealed a Gaussian shaped profile…
Extraneous thermal motion can limit displacement sensitivity and radiation pressure effects, such as optical cooling, in a cavity-optomechanical system. Here we present an active noise suppression scheme and its experimental implementation.…
High-quality quantum oscillators are preferred for precision sensing of external physical parameter because if the noise level due to interactions with the environment is too high, metrological information can be lost due to quantum…
We demonstrate radiation-pressure cavity-cooling of a mechanical mode of a micromirror starting from cryogenic temperatures. To achieve that, a high-finesse Fabry-Perot cavity (F\approx 2200) was actively stabilized inside a continuous-flow…
We study the dynamics of an optical mode in a cavity with a movable mirror subject to quantum Brownian motion. We study the phase noise power spectrum of the output light, and we describe the mirror Brownian motion, which is responsible for…
Thermal noise of a mirror is one of the most important issues in high precision measurements such as gravitational-wave detection or cold damping experiments. It has been pointed out that thermal noise of a mirror with multi-layer coatings…
Understanding thermodynamical measurement noise is of central importance for electrical and optical precision measurements from mass-fabricated semiconductor sensors, where the Brownian motion of charge carriers poses limits, to optical…
In recent years quantum phenomena have been experimentally demonstrated on variety of optomechanical systems ranging from micro-oscillators to photonic crystals. Since single photon couplings are quite small, most experimental approaches…
Optical measurements of a nanoscale silicon optomechanical crystal cavity with a mechanical resonance frequency of 3.6GHz are performed at sub-kelvin temperatures. We infer optical-absorption-induced heating and damping of the mechanical…
Fiber Fabry-Perot cavities, formed by micro-machined mirrors on the end-facets of optical fibers, are used in an increasing number of technical and scientific applications, where they typically require precise stabilization of their optical…
We study high-stress SiN films for reaching the quantum regime with mesoscopic oscillators connected to a room-temperature thermal bath, for which there are stringent requirements on the oscillators' quality factors and frequencies. Our SiN…
Liquid droplet whispering-gallery-mode microresonators open a new research frontier for optomechanics and photonic devices. At visible wavelengths, where most liquids are transparent, a major contribution to a droplet optical quality factor…