Related papers: Operando direct observation of spin states correla…
SCAPS 1-D was used for the simulation of lead-free environmentally benign methylammonium tin-iodide (CH3NH3SnI3) based solar cell. Indium sulphide (In2S3) was utilized as the electron transport layer (ETL) for its high carrier mobility and…
Next-generation low-cost semiconductors such as halide perovskites exhibit optoelectronic properties dominated by nanoscale variations in their structure, composition and photophysics. While microscopy provides a proxy for ultimate device…
This study delves into the effects of doping Spiro-OMeTAD, a widely employed hole transport material (HTM) in perovskite solar cells, with three distinct impurities: lithium bis(trifluoromethanesulfonyl)imide (Li-TFSI), FK209, and…
After the efficiency of organic photovoltaic (OPV) cells achieved more than 10%, the control of stability and degradation mechanisms of solar cells became a prominent task. The improvement of device efficiency due to incorporation of a…
Using a representative translational dimer model, high throughput calculations are implemented for fast screening of a total of 74 diacenaphtho-extended heterocycle (DAH) derivatives as hole transport layer (HTL) materials in perovskite…
Perovskite solar cells (PSCs) without a hole transport layer (HTL) offer a cost-effective and stable alternative to conventional architectures, utilizing only an absorber layer and an electron transport layer (ETL). This study presents a…
In the last few years there is an unprecedented progress in the increase of the power conversion efficiency of perovskite solar cells. Evidently, further advances of the efficiency of these devices will depend on the constraints imposed by…
Perovskite solar cells (PSCs) have emerged as a promising photovoltaic technology, already achieving efficiencies surpassing 25%. However, effects such as hysteresis are commonly observed due to the interplay of ionic and electronic…
Previous studies of reverse-bias stability in perovskite solar cells have focused primarily on voltage controlled reverse-bias tests. Here we instead present an investigation of perovskite solar cell degradation under well-defined, constant…
Correlating the microstructure of an energy conversion device to its performance is often a complex exercise, notably in solid oxide fuel cell (SOFC) research. SOFCs combine multiple materials and interfaces that evolve in time due to high…
In pursuit of an all-inorganic non-toxic perovskite solar cell (PSC) with enhanced performance, we have investigated the rhombohedral phase of the germanium-based rubidium halide perovskites RbGeX$_3$ (X = Cl, Br, I). The structural…
We report that device architecture engineering has a substantial impact on the reverse bias instability that has been reported as a critical issue in commercializing perovskite solar cells. We demonstrate breakdown voltages exceeding -15 V…
Perovskite solar cells have drawn much attention in recent years, owing to its world-record setting photovoltaic performances. Despite its promising use in tandem applications and flexible devices, its practicality is still limited by its…
Organic-inorganic hybrid perovskites (OIHPs) have attracted extensive research interest as a promising candidate for efficient and inexpensive solar cells. Transmission electron microscopy characterizations that can benefit the fundamental…
Lead iodide perovskites have attracted considerable interest in the upcoming photovoltaic technologies and optoelectronic devices. Therefore, an accurate theoretical description of the electronic and optical properties especially to…
Perovskite-based solar cells are promising due to their rapidly improving efficiencies, but suffer from instability issues. Recently it has been claimed that one of the key contributors to the instability of perovskite solar cells is ion…
Efficient charge separation at the interfaces between the perovskite and with the carrier transport layers is crucial for perovskite solar cells to achieve high power conversion efficiency. We systematically investigate the hole injection…
One of the critical challenges in enhancing the performance of perovskite solar cells is reducing the density of trap states in the light-absorbing perovskite layer. These trap states lead to increased charge carrier recombination, thus…
Carbon-electrode-based PSC devices are stressed under 1 Sun equivalent illumination in a stability setup, and different scan-speed dependent current-voltage (J-V) curves are measured during aging. The collected data is used to estimate…
The lead halide perovskites demonstrate huge potential for optoelectronic applications, high energy radiation detectors, light emitting devices and solar energy harvesting. Those materials exhibit strong spin-orbit coupling enabling…