Related papers: Large-scalable fabrication of improved Bi-Te-based…
Superconducting hot-electron bolometers are presently the best performing mixing devices for the frequency range beyond 1.2 THz, where good quality superconductor-insulator-superconductor (SIS) devices do not exist. Their physical…
A thermoelectric device is a heat engine that directly converts heat into electricity. Many materials with a high figure of merit ZT have been discovered in anticipation of a high thermoelectric efficiency. However, there has been a lack of…
Type I superconductivity has recently been reported for the Dirac semimetal PdTe$_2$ (Tc approximately 1.6K) with, remarkably, multiple critical fields and a complex phase diagram. Here, measurements of the specific heat utilizing a thermal…
We demonstrate that the charge-spin conversion efficiency of topological insulators (TI) can be experimentally determined by injecting spin-polarized tunneling electrons into a TI. Through a comparative study between bismuth selenide and…
Many thermo-mechanical processes, such as thermal expansion and stress relaxation, originate at the atomistic scale. We develop a sequential multiscale approach to study thermally stressed superelastic polyimide to explore these effects.…
An efficient approach to improve the thermoelectric performance of materials is to converge their electronic bands, which is known as band engineering. In this regard, lots of effort have been made to further improve the thermoelectric…
Thin crystalline silicon solar photovoltaics holds great potential for reducing the module price by material saving and increasing the efficiency by reduced bulk recombination loss. However, the module efficiency decreases rather…
This work presents for the first time a flexible over-moded resonator (OMR) based on P(VDF-TrFE) thin films. The devices were manufactured on commercially available elastic substrate with inkjet-printed electrodes. The sensing copolymer…
The ongoing demand for more energy-efficient, high-performance electronics is driving the exploration of innovative materials and device architectures, where interfaces play a crucial role due to the continuous downscaling of device…
Bulk superconductivity has been discovered in Tl_{0.6}Bi_{2}Te_{3}, which is derived from the topological insulator Bi2Te3. The superconducting volume fraction of up to 95% (determined from specific heat) with Tc of 2.28 K was observed. The…
We report on an optimized micro-machined thermal flow-rate sensor as part of an autonomous multi-parameter sensing device for water network monitoring. The sensor has been optimized under the following constraints: low power consumption and…
Transparent electrodes (TEs) made of metallic nanowires, such as Ag, Au, Cu, and Ni, have attracted rising attention for several reasons: 1) they can act as a substitute for tin oxide-based TEs such as indium-tin oxide (ITO) and…
Thermophotovoltaics are promising solid-state energy converters for a variety of applications such as grid-scale energy storage, concentrating solar-thermal power, and waste heat recovery. Here, we report the design, fabrication, and…
We propose to operate a superconducting transition edge sensor (TES) using a different type of biasing, in which the resistance of the TES is kept constant by means of feedback on the bias voltage and is independent of the incoming signal…
We present a study of electronic transport in individual Bi nanowires of large diameter relative to the Fermi wavelength. Measurements of the resistance and thermopower of intrinsic and Sn-doped Bi wires with various wire diameters, ranging…
Metal/superconductor/semiconductor (Ag/TlBaCaCuO/CdSe) heterostructures have been successfully fabricated using pulse-electrodeposition technique. The electrochemical parameters are optimized and diffusion free growth of CdSe onto…
We investigate the possibility to obtain a thermal diode with functionally graded Si-Ge alloys. A wire with variable section is considered. After the introduction of a formula giving the thermal conductivity of the wire as a function of the…
We introduce a new property of tile self-assembly systems that we call size-separability. A system is size-separable if every terminal assembly is a constant factor larger than any intermediate assembly. Size-separability is motivated by…
Realizing active metasurfaces with substantial tunability is important for many applications but remains challenging due to difficulties in dynamically tuning light-matter interactions at subwavelength scales. Here, we introduce reversible…
This paper describes the development of metallic bipolar plate fabrication using micro-electroforming process for mini-DMFC (direct methanol fuel cell) stacks. Ultraviolet (UV) lithography was used to define micro-fluidic channels using a…