Related papers: Precise calibration method for triaxial magnetomet…
This paper describes a novel method for calibrating dc-precise magnetometers in the low field range (100 uT), which gives acceptable results even in laboratory conditions with significant magnetic interference. By introducing a closely…
Magnetometers, gyroscopes and accelerometers are commonly used sensors in a variety of applications. The paper proposes a novel gyroscope calibration method in the homogeneous magnetic field by the help of magnetometer. It is shown that,…
In this paper the techniques available to make and calibrate magnetic search coils are reviewed, with emphasis on harmonic coil systems as the commonly-used optimal choice for integral measurements of accelerator magnets in terms of…
Magnetometer has received wide applications in attitude determination and scientific measurements. Calibration is an important step for any practical magnetometer use. The most popular three-axis magnetometer calibration methods are…
A high-accuracy calibration of inductive coil sensors based on Printed Circuit Board (PCB), commonly used in rotating coil field measurements of particle accelerator magnets, is presented. The amplitude and phase of signals with and without…
This paper developed an efficient method for calibrating triaxial MEMS gyroscopes, which can be effectively utilized in the field environment. The core strategy is to utilize the criterion that the dot product of the measured gravity and…
We introduce a methodology to calibrate in situ a set of coils generating bi- or tri-axial magnetic fields, at frequencies where a calibration performed under static conditions would be inaccurate. The methodology uses harmonic analysis of…
In this work we present a practical algorithm for calibrating a magnetometer for the presence of magnetic disturbances and for magnetometer sensor errors. To allow for combining the magnetometer measurements with inertial measurements for…
This paper describes a calibration algorithm to simultaneously calibrate a magnetometer and an accelerometer without any information besides the sensors readings. Using a linear sensor model and maximum likelihood cost, the algorithm is…
In this paper, we propose a method to estimate the position, orientation and gain of a magnetic field sensor using a set of (large) electromagnetic coils. We apply the method for calibrating an array of optically pumped magnetometers (OPMs)…
This paper presents an efficient servomotor-aided calibration method for the triaxial gyroscope. The entire calibration process only requires approximately one minute, and does not require high-precision equipment. This method is based on…
In this paper, we present a triaxial alignment magnetometer based on free-spin precession deployed in the geomagnetic range. Existing vector measurement methods often require complex optical setups, heating structures, and laser modulation.…
This paper presents an efficient in-field calibration method tailored for low-cost triaxial MEMS gyroscopes often used in healthcare applications. Traditional calibration techniques are challenging to implement in clinical settings due to…
Magnetic surveys are conventionally performed by scanning a domain with a portable scalar magnetic sensor. Unfortunately, scalar magnetometers are expensive, power consuming and bulky. In many applications, calibrated vector magnetometers…
A three-step model for calculating the magnetic field generated by coils inside cuboid-shaped shields like magnetically shielded rooms (MSRs) is presented. The shield is modelled as two parallel plates of infinite width and one tube of…
The calibration of MEMS triaxial gyroscopes is crucial for achieving precise attitude estimation for various wearable health monitoring applications. However, gyroscope calibration poses greater challenges compared to accelerometers and…
We present the design and characterization of a ground-based absolute polarization angle calibrator accurate to better than 0.1 degrees for use with polarization sensitive cosmic microwave background (CMB) experiments. The calibrator's…
This is the second of three papers describing an `absolute' calibration of the GONG magnetograph using an end-to-end simulation of its measurement process. In the first paper, we described the GONG instrument and our `end-to-end' simulation…
The paper proposes a novel calibration approach for the Orthoglide-type mechanisms based on observations of the manipulator leg parallelism during motions between the prespecified test postures. It employs a low-cost measuring system…
The paper proposes a novel calibration approach for the Orthoglide-type mechanisms based on observations of the manipulator leg parallelism during mo-tions between the prespecified test postures. It employs a low-cost measuring system…