Related papers: Numerical Contribution of Micro-Pulsed Laser Effec…
Photothermal effects of gold core-shell nanoparticles and nanorods dispersed in water are theoretically investigated using the transient bioheat equation and the extended Mie theory. Properly calculating the absorption cross section is an…
Propagation of high-intensity, high-contrast ($<10^{-8}$), 50\,fs laser pulses through triangilar copper capillaries is experimentally studied. The relative transmission through 20-mm-long, about 50\,$\mu$m wide capillaries is directly…
In this paper, the results of numerical experiments verifying a novel setup for laser beam profiling are presented. The experimental setup is based on infrared thermography and includes laser beam illuminating a thin metal plate. The method…
We present an in-depth analysis of the energy dependence of optical breakdown in water by tightly focused laser pulses, from plasma formation to shock waves and cavitation. Laser pulses of fs to ns durations and UV to IR wavelengths are…
We report on experimental results in a new regime of a relativistic light-matter interaction employing mid-infrared (3.9-micrometer wavelength) high-intensity femtosecond laser pulses. In the laser generated plasma, the electrons reach…
This work proposes an extensive review of laminar and turbulent forced convective heat transfer correlations inside tubes by analyzing both experimental and computational research. Convective heat transfer is influenced by fluid turbulence…
On the basis of ab initio quantum mechanics (QM) calculation, the obtained electron heat capacity is implemented into energy equation of electron subsystem in two temperature model (TTM). Upon laser irradiation on the copper film, energy…
In this research, wettability control by area fraction of laser ablated surface of copper is presented. The functional surfaces with full wettability control from highly hydrophilic to super-hydrophobic were created on copper by nanosecond…
Silicon irradiated with an ultrashort 800 nm-laser pulse is studied theoretically using a two temperature description that considers the transient free carrier density during and after irradiation. A Drude model is implemented to account…
Ablation of Cu and Al targets has been performed with 170 fs laser pulses in the intensity range of 10^12-10^14 W/cm^2. We compare the measured removal depth with 1D hydrodynamic simulations. The electron-ion temperature decoupling is taken…
Nanoscale thermally assisted hydrodynamic melt perturbations induced by ultrafast laser energy deposition in noble-metal films produce irreversible nanoscale translative mass redistributions and results in formation of radially-symmetric…
Coherent x-ray micro-diffraction and local mechanical loading can be combined to investigate the mechanical deformation in crystalline nanostructures. Here we present measurements of plastic deformation in a copper crystal of sub-micron…
Upon the excitation by an ultrashort laser pulse the conditions in a material can drastically change, altering its optical properties and therefore the relative amount of absorbed energy, a quan- tity relevant for determining the damage…
This article reports on the influence of laser irradiation onto the electrical conductance of gold nanocontacts established with the mechanically controllable breakjunction technique (MCB). We concentrate here on the study of reversible…
The objective of this work is to investigate the coupling of fluid dynamics, heat transfer and mass transfer during the impact and evaporation of droplets on a heated solid substrate. A laser-based thermoreflectance method is used to…
In this paper the interaction of attosecond laser pulses with matter is investigated. The scattering and potential motion of heat carriers as well as the external force are considered. Depending on the ratio of the scatterings and potential…
Control over the properties of nanoparticles obtained by laser ablation in liquids is experimentally demonstrated via modulation of the beam intensity profile on the target. Mask projection scheme was used with either a copper laser…
High power lasers are used for a variety of manufacturing processes on time and length scales that cover many orders of magnitude and on different materials. The variety of processes achievable through laser-material interaction results…
We investigate melting and undercooling in nanoscale (radius ~100 nm) gold particles that are levitated in a quadrupole ion (Paul) trap in a high vacuum environment. The particle is heated via laser illumination and probed using two main…
Ultrafast laser induced thermionic emission from metal surfaces has several applications. Here, we investigate the role of laser polarization and angle of incidence on the ultrafast thermionic emission process from laser driven gold coated…