Related papers: Synthesis, properties and thermal decomposition of…
MAX phases have great potential under demands of both high-temperature and high-stress performance, with their mixed atomic bonding producing the temperature and oxidation resistance of ceramics with the mechanical resilience of metals.…
Ultra-high temperature ceramics (UHTCs) are promising materials for use in next-generation aerospace structures but have primarily been used as monolithic materials or coatings due to processing limitations. Here, new functionality (e.g.,…
A mechanism to explain the lower onset strengthening temperature induced by CaCO$_3$ in alumina-based macroporous ceramics is proposed, which relies on hydrocalumite-like phase formation during processing. Close to 600$^\circ$C, such phases…
Textured alumina ceramics were obtained by Spark Plasma Sintering (SPS) of undoped commercial a-Al2O3 powders. Various parameters (density, grain growth, grain size distribution) of the alumina ceramics, sintered at two typical temperatures…
Potassium tantalate (KTaO$_{3}$) is a promising material for dielectric applications at low temperature. However, dense and single-phase ceramics cannot be obtained by conventional sintering because of the evaporation of potassium that…
Herein we report on the synthesis of a metastable (Cr,Y)2AlC MAX phase solid solution by co-sputtering from a composite Cr-Al-C and elemental Y target, at room temperature, followed by annealing. While direct high-temperature synthesis…
We report the decomposition of La2-xSrxCuO4 into La2O3 and Cu nanoparticles in ultra-high vacuum, observed by in-situ heating experiments in a transmission electron microscope (TEM). The analysis of electron diffraction data reveals that…
High-pressure techniques open exploration of functional materials in broad research fields. An established diamond anvil cell with a boron-doped diamond heater and transport measurement terminals has performed the high-pressure synthesis of…
Ceramics are typically brittle at ambient conditions due to their covalent or ionic bonding and limited dislocation activities. While plasticity, and occasionally superplasticity, can be achieved in ceramics at high temperatures through…
We report experimental discovery of tantalum polyhydride superconductor. It was synthesized at high pressure and high temperature conditions using diamond anvil cell combined with in-situ high pressure laser heating techniques. The…
Silicon-based MAX phases are a promising class of layered ceramics with superior thermal and chemical stability. However, their synthesis remains challenging due to inherent thermodynamic instability at high temperatures. Herein, we develop…
In the present investigation the pure elemental powder mixture of Al (70 at%) Ni (15 at %), Cu (15 at %) was mechanically milled in an attritor ball mill for 10, 20, 40, 60, 80 and 100 hours in hexane medium at 400 rpm. The isothermal…
Ceramics are highly technical materials with properties of interest for multiple industries. Precisely because of their high chemical, thermal, and mechanical resistance, ceramics are difficult to mold into complex shapes. A possibility to…
A high density CaKFe$_4$As$_4$ bulk sample was successfully synthesized using a spark plasma sintering (SPS) technique. The density of the synthesized sample was 5.02 g cm$^{-3}$, corresponding to 96.2% of the theoretical density of…
Phase-pure synthesis has been a major challenge for metal oxynitrides due to their sensitivity to synthesis conditions and the limited understanding of the underlying thermodynamics. The beta-phase tantalum oxynitride (beta-TaON), a…
Coatings of (Al1-xVx)2O3, with x ranging from 0 to 1, were deposited by pulsed DC reactive sputter deposition on Si(100) at a temperature of 550 {\deg}C. XRD showed three different crystal structures depending on V-metal fraction in the…
Herein we report on the thermal expansions and temperature-dependent crystal structures of select ternary carbide MAX phases in the Ti-Al-C phase diagram in the 100-1000 deg C temperature range. A bulk sample containing 38 wt.% Ti5Al2C3,…
We show here for the first time the use of a cold sintering process (CSP) to sinter CoSb3-based thermoelectric materials. CSP at 150 {\deg}C for 90 min under a uniaxial pressure of 750 MPa yields pieces with a relative density of 86 %,…
A series of FeSe0.5Te0.5 bulk samples have been prepared through the high gas pressure and high-temperature synthesis (HP-HTS) method to optimize the growth conditions, for the first time and investigated for their superconducting…
The high pressure and high temperature phase diagram of Ta has been studied in a laser-heated diamond-anvil cell (DAC) using x-ray diffraction measurements up to 52 GPa and 3800 K. The melting was observed at nine different pressures, being…