Related papers: A Low-Power 20-Gb/s Discrete-Time Analog Front-End…
Using digital standard cells and digital place-and-route (PnR) tools, we created a 20 GS/s, 8-bit analog-to-digital converter (ADC) for use in high-speed serial link applications with an ENOB of 5.6, a DNL of 0.96 LSB, and an INL of 2.39…
The ubiquitous use of sensing and signal processing is increasing exponentially with the advance of the Internet of Everything (IoE). In this context, the design of every time more power efficient sensor nodes is a must. Within these nodes,…
An ADC is used to convert analog signals into binary signals. Compared with many other types of ADCs, flash converters are incredibly quick. A typical Flash ADC consists of 2n resistors, 2n-1 op-amp comparators, and an encoder which…
In a high-speed coherent optical transmission system, typically the signals obtained at the receiver front-end are digitized using very high-speed ADCs and then processed in the digital domain to remove optical channel impairments. In this…
With the advent of the 5G wireless networks, achieving tens of gigabits per second throughputs and low, milliseconds, latency has become a reality. This level of performance will fuel numerous real-time applications, such as autonomy and…
This paper presents the design of a time-division multiplexed capacitively-coupled chopper analog front-end (AFE) with a novel impedance boost loop (IBL) and a novel DC servo loop (DSL). The proposed IBL has two impedance booting loops for…
The design and measurement results of ultra-low power, fast 10-bit Successive Approximation Register (SAR) Analog-to-Digital Converter (ADC) prototypes in 65 nm CMOS technology are presented. Eight prototype ADCs were designed using two…
This paper describes a pipelined analog-to-digital converter (ADC) employing a power and area efficient architecture. The adjacent stages of a pipeline share operational amplifiers. In order to keep accuracy of the amplifiers in the first…
Comparators are utilised by Nyquist-rate and oversampling analog to digital converters (ADCs) to accomplish quantization and perhaps sampling. Thus, comparators have a substantial effect on the speed and accuracy of ADCs. This study…
We present the design of a low-power 4-bit 1GS/s folding-flash ADC with a folding factor of two. The design of a new unbalanced double-tail dynamic comparator affords an ultra-low power operation and a high dynamic range. Unlike the…
This paper presents a low-power 10-bit 130-MS/s successive approximation register (SAR) analog-to-digital converter (ADC) in 90 nm CMOS process. The proposed asynchronous ADC consists of a comparator, SAR logic block and two control blocks…
With the new generation of the RPC, it is possible to work with induced signals of hundreds $\mu V$, hence the front-end electronics is an important and delicate part of the detector in order to get a detectable signal. The electronic chain…
Dynamic comparators are the core of high-speed, high-resolution analog-to-digital converters (ADCs) used for communication applications. Most of the dynamic comparators attain high-speed operation only for sufficiently high input difference…
A 6bit flash-ADC with 1.2GSps, wide analog bandwidth and low power, realized in a standard digital 0.13 $\mu$m CMOS copper technology is presented. Employing capacitive interpolation gives various advantages when designing for low power: no…
Dynamic comparators are an essential part of low-power analog to digital converters (ADCs) and are referred to as one of the most important building blocks in mixed mode circuits. The power consumption and accuracy of dynamic comparators…
In most digital-to-time converter (DTC) based applications, apart from maintaining low integral non-linearity (INL), it is also required of the system to achieve a wide frequency translation range. To achieve this performance, we present a…
A 33.6 ps LSB Time-to-Digital converter was designed in 130 nm BiCMOS technology. The core of the converter is a differential 9-stage ring oscillator, based on a multi-path architecture. A novel version of this design is proposed, along…
With the advancement in the field of the Internet of Things(IoT) and Internet of Bodies(IoB), video camera applications using Video Sensor Nodes(VSNs) have gained importance in the field of autonomous driving, health monitoring, robot…
A novel background calibration technique for Time-Interleaved Analog-to-Digital Converters (TI-ADCs) is presented in this paper. This technique is applicable to equalized digital communication receivers. As shown by Tsai et al. [1] and Luna…
The purpose of this project was to design and implement a pipeline Analog-to-Digital Converter using 0.35um CMOS technology. Initial requirements of a 25-MHz conversion rate and 8-bits of resolution where the only given ones. Although…