Related papers: Realisation of Highly Precise and Low Power Tunabl…
This paper describes the architecture of first and second generation current conveyor (CCI and CCII respectively) and designing an amplifier using second generation current conveyor. The designed amplifier through CCII+ can be used in…
A robust square wave generator employing a sole capacitor and two resistors has been presented in this study. Low power and popular translinear circuit scheme of Second generation current controlled current conveyor-CCCII has been taken as…
The paper presents a current tunable multifunction filter using current conveyor. The proposed circuit can be realized as on chip tunable low pass, high pass, band pass and elliptical notch filter. The circuit employs two current conveyors,…
The paper presents a current conveyor based multifunction filter. The proposed circuit can be realized as low pass, high pass, band pass and elliptical notch filter. The circuit employs two balanced output current conveyors, four resistors…
In this paper, a circuit employing current controlled current conveyor trans-conductance amplifiers (CCCCTAs) as active element is proposed which can function both as biquad filter and oscillator. It uses two CCCCTAs and two capacitors. As…
A transimpedance amplifier has been designed for scanning tunneling microscopy (STM). The amplifier features low noise (limited by the Johnson noise of the 1 G{\Omega} feedback resistor at low input current and low frequencies), sufficient…
The task of this work was to design and later produce a low-power (single supply 5 - 30 V, dual supply +-2.5 V and +-15 V) rail-to-rail operational amplifier aRD820 with low voltage noise (<4 uV, p-p. 0.1 to 10 Hz), ultralow input bias…
In this paper a CMOS operational amplifier is presented which operates at 2V power supply and 1microA input bias current at 0.8 micron technology using non conventional mode of operation of MOS transistors and whose input is depended on…
In this work, a new method for designing an analog circuit for deep sub-micron CMOS fabrication processes is proposed. The proposed method leverages the regression algorithms with the transistor circuit model to size a transistor in 0.18 um…
This paper proposes a new topology of a non-isolated two-phase interleaved boost DC-DC converters with modified Greinacher voltage multiplier cells (VMCs) in continuous conduction mode (CCM). The proposed topology can quickly achieve a high…
Power consumption has emerged as a primary design constraint for integrated circuits (ICs). In the Nano meter technology regime, leakage power has become a major component of total power. Full adder is the basic functional unit of an ALU.…
This paper investigates the impact of technological constraints on passive elements in the design of inductively degenerated CMOS low-noise amplifiers (LNAs). A theoretical analysis is combined with circuit simulations in a 130-nm CMOS…
We propose a new type of cryogenic current amplifiers, in which low-frequency power spectrum of current can be measured through a measurement of microwave response of a superconducting resonant circuit shunted by a series array of Josephson…
As transistor sizes reach the mesoscopic scale, the limitations of traditional methods in ensuring thermodynamic consistency have made power dissipation optimization in transistor amplifiers a critical challenge. Based on stochastic…
A low-noise amplifier (LNA) amplifies a very low-power signal without significantly degrading its signal-to-noise ratio. This paper provides the design of a linear low noise amplifier with the transistor BFP 640 using bilateral approach…
As the Internet of Things (IOT) is growing rapidly, there is an emerging need to facilitate development of IOT devices in the design cycle while optimized performance is obtained in the field of operation. This paper develops…
Nanopositioning techniques currently applied to characterize physical properties of materials interesting for applications at the microscopic scale rely on high-voltage electronic control circuits that should have the lowest possible noise…
We describe a calibration setup for the transresistance of low-current amplifiers, based on the capacitance-charging method. The calibration can be performed in the current range of typical interest for electron counting experiments. The…
This paper proposes a low-power and low-noise instrumentation amplifier (IA) tailored for bioimpedance sensing applications. The design originates from a gain-boosted flipped voltage follower (FVF) transconductance (TC) stage and integrates…
A family of interleaved current-fed high step-up dc-dc converters are introduced and analyzed here by combining a voltage multiplier (VM) and an active clamp circuit for high-voltage high-power applications. Low input currents and output…