Related papers: A minimal-length approach unifies rigidity in unde…
When elastic solids are sheared, a nonlinear effect named after Poynting gives rise to normal stresses or changes in volume. We provide a novel relation between the Poynting effect and the microscopic Gr\"uneisen parameter, which quantifies…
The origin of rigidity in disordered materials is an outstanding open problem in statistical physics. Previously, a class of 2D cellular models has been shown to undergo a rigidity transition controlled by a mechanical parameter that…
Disordered spring networks that are undercoordinated may abruptly rigidify when sufficient strain is applied. Since the deformation in response to applied strain does not change the generic quantifiers of network architecture - the number…
This paper is motivated by the complex blister patterns sometimes seen in thin elastic films on thick, compliant substrates. These patterns are often induced by an elastic misfit which compresses the film. Blistering permits the film to…
In both nature and engineering, loosely packed granular materials are often compacted inside confined geometries. Here, we explore such behaviour in a quasi-two dimensional geometry, where parallel rigid walls provide the confinement. We…
In the present work, the overall nonlinear elastic behavior of a 1D multi-modular structure incorporating possible imperfections at the discrete (micro-scale) level, is derived with respect to both tensile and compressive applied loads. The…
When sheared, most elastic solids such as metals, rubbers and polymer hydrogels dilate in the direction perpendicular to the shear plane. This well-known behaviour known as the Poynting effect is characterized by a positive normal stress.…
The main result of this work is a homogenization theorem via variational convergence for elastic materials with stiff checkerboard-type heterogeneities under the assumptions of physical growth and non-self-interpenetration. While the…
This paper constructs the first mixed finite element for the linear elasticity problem in 3D using $P_3$ polynomials for the stress and discontinuous $P_2$ polynomials for the displacement on tetrahedral meshes under some mild mesh…
Bending the edge of a thin elastic material promotes rigidity far from its clamped boundary. However, this curvature-induced rigidity can be overwhelmed by gravity or other external loading, resulting in elastic buckling and large…
The hardness of materials plays an important role in material design. There are numerous experimental methods to measure the hardness of materials, but theoretical prediction of hardness is challenging. By investigating the correlation…
Microstructural evolution in structural materials is known to occur in response to mechanical loading and can often accommodate substantial plastic deformation through the coupled motion of grain boundaries (GBs). This can produce desirable…
Differential shrinkage in particulate quasi-brittle materials causes microcracking which reduces durability in these materials by increasing their mass transport properties. A hydro-mechanical three-dimensional periodic network approach was…
Disordered filamentous networks with compliant crosslinks exhibit a low linear elastic shear modulus at small strains, but stiffen dramatically at high strains. Experiments have shown that the elastic modulus can increase by up to three…
Cutting mechanics in soft solids have been a subject of study for several decades, an interest fuelled by the multitude of its applications, including material testing, manufacturing, and biomedical technology. Wire cutting is the simplest…
Some remarkable generic properties, related to isostaticity and potential energy minimization, of equilibrium configurations of assemblies of rigid, frictionless grains are studied. Isostaticity -the uniqueness of the forces, once the list…
The shear-modulus and yield-stress of amorphous solids are important material parameters, with the former determining the rate of increase of stress under external strain and the latter being the stress value at which the material flows in…
We investigate a minimal model of the plastic deformation of amorphous materials. The material elements are assumed to exhibit ideally plastic behavior (J2 plasticity). Structural disorder is considered in terms of random variations of the…
In this paper, we study the preferential stiffness and the crack-tip fields for an elastic porous solid of which material properties are dependent upon the density. Such a description is necessary to describe the failure that can be caused…
Our goal is to develop a design framework for multifunctional mechanical metamaterials that can tune their rigidity while optimizing other desired properties. Towards this goal, we first demonstrate that underconstrained central force…