Related papers: Underlying burning resistant mechanisms for titani…
In this paper, we present a concept to fabricate copper based Ti2AlC MAX phase composite focusing on the processing method and the reaction which takes place at the matrix-reinforcement interface to yield 2D TiCx. Copper was reinforced with…
We investigate the thermodynamics and phase stability of the AlTiVCr lightweight high-entropy alloy using a combination of ab initio electronic structure calculations, a concentration wave analysis, and atomistic Monte Carlo simulations. In…
The high strength of structural aluminium alloys depends strongly on the controlled precipitation of specific intermetallic phases, whose identity and crystal structure can be difficult to predict. Here, we investigate the Al-Pt system,…
Carbon solubility in face-centered cubic Ni-W alloys and the phase diagram of C-Ni-W are investigated by means of first principle calculations and semi-grand canonical Monte Carlo simulations. With density functional theory (DFT) total…
ODS steels based on yttrium oxide have been suggested as potential fusion reactor wall materials due to their observed radiation resistance properties. Presumably this radiation resistance can be related to the interaction of the particle…
The binary Re$_{1-x}$Mo$_x$ alloys, known to cover the full range of solid solutions, were successfully synthesized and their crystal structures and physical properties investigated via powder x-ray diffraction, electrical resistivity,…
The influence of Sn alloying additions on the aqueous passivation behavior of Cu-Al alloys was revisited and found to function as a new third element effect in acidified 0.1 M Na2SO4 solution. The role of each element during the process of…
Contrary to prior calculations, the Ni-rich ordered structures of the Cr-Ni alloy system are found to be antiferromagnetic under semi-local density-functional theory. The optimization of local magnetic moments significantly increases the…
The present work focuses on the investigation of the thermal stability and structural integrity of amorphous alumina coatings intended for use as protective coatings on cladding tubes in Generation IV nuclear reactors, specifically in the…
To rectify the problems of electron clouds observed in RHIC and unacceptable ohmic heating for superconducting magnets that can limit future machine upgrades, we started developing a robotic plasma deposition technique for $in-situ$ coating…
Tungsten-copper (W-Cu) compounds are widely utilized in various industrial fields due to their exceptional mechanical properties. In this study, we have developed a neural-network-based deep potential (DP) model that covers a wide range of…
A total of 5 different half-Heusler alloys, two p-type and two n-type with the fifth a charge compensated alloy have been designed and synthesized. The thermophysical properties of these alloys have been investigated in the range 10 K to…
Ductile metals undergo a considerable amount of plastic deformation before failure. Void nucleation, growth and coalescence is the mechanism of failure in such metals. {\alpha}/{\beta} titanium alloys are ductile in nature and are widely…
Photocatalytic nitrogen fixation provides a promising route to produce reactive nitrogen compounds at benign conditions. Titania has been reported as an active photocatalyst for reduction of dinitrogen to ammonia; however there is little…
This study investigates hydrogen permeation in titanium aluminium nitride (TiAlN) using ab initio density functional theory (DFT) for cubic and hexagonal crystal structures. Despite the significance of hydrogen barriers, the potential of…
We demonstrate a substantial reduction in two-level system loss in tantalum coplanar waveguide resonators fabricated on high-resistivity silicon substrates through the use of an ultrathin titanium sacrificial layer. A 0.2nm titanium film,…
Additive manufacturing (AM) of titanium (Ti) and Ti-6Al-4V lattices has been proposed for bone implants and augmentation devices. Ti and Ti-6Al-4V have favourable biocompatibility, corrosion resistance and fatigue strength for bone…
Both superconductivity and thermoelectricity offer promising prospects for daily energy efficiency applications. The advancements of thermoelectric materials have led to the huge improvement of the thermoelectric figure of merit in the past…
We propose an explanation for the recently observed non-Fermi-liquid behavior of metallic alloys CeCu_{6-x}Au_x: near x=0.1, the specific heat c is proportional to T \ln (T_0/T) and the resistivity increases linearly with temperature T over…
By combining first principles transition state location and molecular dynamics simulation, we unambiguously identify a carbon atom approaching induced bridging metal structure formation on Cu (111) surface, which strongly modify the carbon…