Related papers: Creep dynamics of athermal amorphous materials: a …
We study the two-dimensional (2D) shear flow of amorphous solids within variants of an elastoplastic model, paying particular attention to spatial correlations and time fluctuations of, e.g., local stresses. The model is based on the local…
The slow flow of amorphous solids exhibits striking heterogeneities: swift localised particle rearrangements take place in the midst of a more or less homogeneously deforming medium. Recently, experimental as well as numerical work has…
An extremal model for the plasticity of amorphous materials is studied in a simple two-dimensional anti-plane geometry. The steady-state is analyzed through numerical simulations. Long-range spatial and temporal correlations in local slip…
Most materials age, and their properties change over time. The aging of materials is reflected in their mechanical responses to external stress and strain, which exhibit logarithmic relaxation and universal power-law creep. Those responses…
Sloped terrains tend to creep downward over time, even when their slope is below the nominal angle of repose. This behavior can result from periodic variations in environmental conditions, such as daily or seasonal fluctuations in…
We study the steady state of driven elastic strings in disordered media below the depinning threshold. In the low-temperature limit, for a fixed sample, the steady state is dominated by a single configuration, which we determine exactly…
We investigate stresses and particle motion during the start up of flow in a colloidal dispersion close to arrest into a glassy state. A combination of molecular dynamics simulation, mode coupling theory and confocal microscopy experiment…
The yield stress is a defining feature of amorphous materials which is difficult to analyze theoretically, because it stems from the strongly non-linear response of an arrested solid to an applied deformation. Mode-coupling theory predicts…
The ubiquitous wall slip behavior of viscoplastic fluids renders the analysis of their steady torsional flow data to determine their yield stress and other parameters of their shear viscosity material function challenging. Roughened…
We study a mean field elastoplastic model, embedded within a disordered landscape of local yield barriers, to shed light on the behaviour of athermal amorphous solids subject to oscillatory shear. We show that the model presents a genuine…
We present an extensive numerical study of dynamical heterogeneities and their influence on diffusion in an athermal mesoscopic model for actively deformed amorphous solids. At low strain rates the stress dynamics are governed by…
We present results from microscopic mode coupling theory generalized to colloidal dispersions under shear in an integration-through-transients formalism. Stress-strain curves in start-up shear, flow curves, and normal stresses are…
Disordered materials under an imposed forcing can display creep and aging effects, accompanied by intermittent, spatially heterogeneous dynamics. We propose a unifying microscopic description of these phenomena, based on the notion that as…
Plastic deformation of crystalline and amorphous matter often involves intermittent local strain burst events. To understand the physical background of the phenomenon a minimal stochastic mesoscopic model was introduced, where…
Far from equilibrium, amorphous solids exhibit structural relaxations that span a vast range of timescales such as physical aging and creep. Recently, it has been shown that such relaxations are driven by via intermittent, scale-free, yet…
We study the yielding transition of a two dimensional amorphous system under shear by using a mesoscopic elasto-plastic model. The model combines a full (tensorial) description of the elastic interactions in the system, and the possibility…
We study creep flow and yielding of particulate depletion gels under constant shear stress, combining data on different length and time scales. We characterise the breakage of meso-scale strands in the gel. Breakage events are distributed…
Tensile creep tests, tensile relaxation tests and a tensile test with a constant rate of strain are performed on injection-molded isotactic polypropylene at room temperature in the vicinity of the yield point. A constitutive model is…
We study the flow behavior and unjamming transition in dense assemblies of actively deforming particles that periodically change size, a process that we refer to as breathing. Using extensive molecular dynamics simulations and a…
We study the dynamics of the solid to liquid transition for a model material made of elastic particles immersed in a viscous fluid. The interaction between particle surfaces includes their viscous lubrication, a sharp repulsion when they…