Related papers: Blind Receive Beamforming for Autonomous Grant-Fre…
In this paper, we propose a joint beamforming algorithm for a multiuser wireless information and power transfer (MU-WIPT) system that is compatible with the conventional multiuser multiple input multiple output (MU-MIMO) system. The…
Simultaneous wireless information and power transfer (SWIPT) is a promising technology for the upcoming sixth-generation (6G) communication networks, enabling internet of things (IoT) devices and sensors to extend their operational…
In this paper, we consider fast wireless data aggregation via over-the-air computation (AirComp) in Internet of Things (IoT) networks, where an access point (AP) with multiple antennas aim to recover the arithmetic mean of sensory data from…
Integrated sensing and communication (ISAC) has been envisioned as a solution to realize the sensing capability required for emerging applications in wireless networks, while efficiently utilizing the available spectral, hardware and energy…
At present, there is a trend to deploy ubiquitous artificial intelligence (AI) applications at the edge of the network. As a promising framework that enables secure edge intelligence, federated learning (FL) has received widespread…
Multimode fibers are attractive for a variety of applications such as internet data transfer, data center hubs, micromanipulation, optogenetics and other biomedical applications. A major hurdle for imaging through multimode fibers is the…
The Internet of Things (IoT) could enable the development of cloud multiple-input multiple-output (MIMO) systems where internet-enabled devices can work as distributed transmission/reception entities. We expect that spatial multiplexing…
This work gives a blind beamforming strategy for intelligent reflecting surface (IRS), aiming to boost the received signal-to-noise ratio (SNR) by coordinating phase shifts across reflective elements in the absence of channel information.…
Millimeter wave (mmWave) communication, utilizing beamforming techniques to address the inherent path loss limitation, is considered as one of the key technologies to support ever increasing high throughput and low latency demands of…
This paper focuses on advancing outdoor wireless systems to better support ubiquitous extended reality (XR) applications, and close the gap with current indoor wireless transmission capabilities. We propose a hybrid knowledge-data driven…
Massive machine-type communications (mMTC) is a crucial scenario to support booming Internet of Things (IoTs) applications. In mMTC, although a large number of devices are registered to an access point (AP), very few of them are active with…
The performance of Simultaneous Wireless Information and Power Transfer (SWIPT) is mainly constrained by the received Radio-Frequency (RF) signal strength. To tackle this problem, we introduce an Intelligent Reflecting Surface (IRS) to…
Conventional beamforming methods for intelligent reflecting surfaces (IRSs) or reconfigurable intelligent surfaces (RISs) typically entail the full channel state information (CSI). However, the computational cost of channel acquisition…
The emerging Internet of Things (IoT) and bidirectional communications in smart grid are expected to improve smart grid capabilities and electricity management. Because of massive number of IoT devices in smart grid, size of the data to be…
Beamforming is the key enabler for wireless communications in the mmWave bands. 802.11ad and WiGig are wireless technologies that currently use the 60 GHz unlicensed mmWave spectrum via beamforming techniques. It is likely that 5G systems…
Traditional simultaneous wireless information and power transfer (SWIPT) with power splitting assumes perfect channel state information (CSI), which is difficult to obtain especially in the massive multiple-input-multiple-output (MIMO)…
Hybrid analog and digital (HAD) beamforming has been recently receiving considerable deserved attention for a practical implementation on the large-scale antenna systems. As compared to full digital beamforming, partial-connected HAD…
Beamforming techniques are utilized in millimeter wave (mmWave) communication to address the inherent path loss limitation, thereby establishing and maintaining reliable connections. However, adopting standard defined beamforming approach…
Ambient radio frequency (RF) energy harvesting is widely promoted as an enabler for wireless-power Internet of Things (IoT) networks. This paper jointly characterizes energy harvesting and packet transmissions in grant-free opportunistic…
Over-the-air computation (AirComp) is a promising technology that is capable of achieving fast data aggregation in Internet of Things (IoT) networks. The mean-squared error (MSE) performance of AirComp is bottlenecked by the unfavorable…