Related papers: Injection Bucket Jitter Compensation Using Phase L…
For the PIP-II program, transverse emittance in the Fermilab Booster must remain well controlled at higher bunch intensities. 4-plate beam position monitors (BPMs) have a small but measurable quadrupole moment, making it possible to infer…
We demonstrate ultra-low timing jitter optical pulse trains from free- running, 80 MHz repetition rate, mode-locked Yb-fiber lasers. Timing jitter of various mode-locking conditions at close-to-zero intra-cavity dispersion (-0.004 to +0.002…
Many present and future accelerators must operate with high intensity beams when distortions induced by space charge forces are among major limiting factors. Betatron tune depression of above approximately 0.1 per cell leads to significant…
Frequency combs from continuous-wave-driven Kerr-nonlinear microresonators have evolved into a key photonic technology with applications from optical communication to precision spectroscopy. Essential to many of these applications is the…
We demonstrate the use of a flexible digital servo system for the optical stabilization of both the repetition rate and carrier-envelope offset frequency of a laser frequency comb. The servo system is based entirely on a low-cost field…
The kicker control system was used for beam extraction and injection between two cooling storage rings (CSRs) at the Heavy Ion Research Facility in Lanzhou (HIRFL). To meet the requirements of special physics experiments, the kicker…
The upcoming Proton Improvement Plan-II (PIP-II), designated for enhancements to the Fermilab accelerator complex, features a new 800 MeV superconducting linac and a Beam Transfer Line (BTL) to transport the beam to the existing Booster…
The Fermilab Booster - built more than 40 years ago - operates well above the design proton beam intensity of 4x10**12 ppp. Still, the Fermilab neutrino experiments call for even higher intensity of 5.5x10**12 ppp. A multitude of intensity…
Multimode lasers have a very complex dynamics, as expected when oscillators are nonlinearly coupled. Order emerges when the modes lock together; in this case the coherent superposition of the modes results into a periodic train of pulses or…
A system for bunch-by-bunch detection of transverse proton and antiproton coherent oscillations in the Fermilab Tevatron collider is described. It is based on the signal from a single beam-position monitor located in a region of the ring…
The measurement of beam emittances by extracting the quadrupole mode signal from a 4 plate beam position monitor (BPM) was published at least 40 years ago. Unfortunately, in practice, this method suffers from poor signal to noise ratio and…
We discuss distributed reframing control of bittide systems. In a bittide system, multiple processors synchronize by monitoring communication over the network. The processors remain in logical synchrony by controlling the timing of frame…
The counting and control of optical cycles of light has become common with modelocked laser frequency combs. But even with advances in laser technology, modelocked laser combs remain bulk-component devices that are hand-assembled. In…
The influence of optical feedback on semiconductor lasers has been a widely studied field of research due to fundamental interests as well as the optimization of optical data transmission and computing. Recent publications have shown that…
Space gravitational wave detectors employing laser interferometry between free-flying spacecraft differ in many ways from their laboratory counterparts. Among these differences is the fact that, in space, the end-masses will be moving…
An electron cloud instability might limit the intensity in the Fermilab Recycler after the PIP-II upgrade. A multibunch instability typically develops in the horizontal plane within a hundred turns and, in certain conditions, leads to beam…
We demonstrate a flux locking technique using injected heat current to linearize the output of a superfluid helium-4 interferometer. A rotation flux through the interferometer loop produces a shift in the phase of the superfluid order…
It is important to have experimental methods to estimate the maximum beam intensity for the Fermilab Booster as objective input into long term program commitments. An important existing limit is set by the available rf power. This limit is…
Beam stacking allows a Fixed Field alternating gradient Accelerator (FFA) to increase the extracted beam current whilst also allowing for a flexible time structure making FFAs a promising candidate for future spallation neutron sources and…
The readout electronics for the resonant beam position monitors (BPMs) in the Fermilab Switchyard (SY) have been upgraded, utilizing a low noise amplifier transition board and Fermilab designed digitizer boards. The stripline BPMs are…