Related papers: Anisotropic coalescence criterion for nanoporous m…
In order to improve the understanding of damage evolution in mechanically heterogeneous microstructures, like the ones of dual-phase steels, the influence of the applied stress state is a key element. In this work, we studied the influence…
The influence of the microstructure of a polycrystalline material on its macroscopic deformation response is still one of the major problems in materials engineering. For materials characterized by elastic-plastic deformation responses,…
The yield surface in crystal plasticity can be approached from various directions during mechanical loading. We consider the competition between nanoindentation and tensile loading towards plastic yielding. For this purpose, we develop a…
Stochastic models for pore collapse in granular materials are developed. First, a general fluctuating stress-strain relation for a plastic flow rule is derived. The fluctuations account for non-associativity in plastic deformations…
Transparent Al2O3 ceramics have attracted considerable interest for use in a wide range of optical, electronic and structural applications. The fabrication of these ceramics using powder metallurgy processes requires the development of…
In order to enhance the modeling of metallic materials behavior in non proportional loadings, a modification of the classical elastic-plastic models including distortion of the yield surface is proposed. The new yield criterion uses the…
In fracture mechanics, polyacrylamide hydrogels have been widely used as a model material for experiments, benefited from its optical transparency, fracture brittleness, and low Rayleigh wave velocity. To describe the brittle fracture in…
Built on the tenets of rational thermodynamics, this article proposes a theory of strain gradient thermo-visco-plasticity for isotropic polycrystalline materials under high strain rates. The effect of micro-inertia, which arises due to…
An improved linear model is developed for elasto-plastic and adhesive contact. New correlations are proposed and validated to estimate the key input parameters of the model, including contact stiffness, yield point, maximum pull-off force…
Are the cohesive laws of interfaces sufficient for modelling fracture in polycrystals using the cohesive zone model? We examine this question by comparing a fully atomistic simulation of a silicon polycrystal to a finite element simulation…
A non-linear history-dependent cohesive zone model of crack propagation in linear elastic and visco-elastic materials is presented. The viscoelasticity is described by a linear Volterra integral operator in time. The normal stress on the…
A crucially important material parameter for all amorphous solids is the yield stress, which is the value of the stress for which the material yields to plastic flow when it is strained quasi-statically at zero temperature. It is difficult…
The confinement of an ionic liquid between charged solid surfaces is treated using an exactly solvable 1D Coulomb gas model. The theory highlights the importance of two dimensionless parameters: the fugacity of the ionic liquid, and the…
A force balance condition to predict quasistatic crack paths in anisotropic brittle materials is derived from an analysis of diffuse interface continuum models that describe both short-scale failure inside a microscopic process zone and…
The coarse-graining of amorphous plasticity from the atomistic to the mesoscopic scale is studied in the framework of a simple scalar elasto-plastic model. Building on recent results obtained on the atomistic scale, we discuss the interest…
Liquid adsorption in nanoporous materials induces their deformation due to strong capillary forces. The linear relationship between the liquid pressure and the solid strain (pore-load modulus) provides an experimental technique to determine…
The coalescence between growing droplets is important for the surface coverage and spatial arrangements of droplets on surfaces. In this work, total internal reflection fluorescence (TIRF) microscopy is utilized to in-situ investigate the…
We investigate elastic-plastic adhesive wear via a continuum variational phase-field approach. The model seamlessly captures the transition from perfectly brittle, over quasi-brittle to elastic-plastic wear regimes, as the ductility of the…
An indentation experiment involves five variables: indenter shape, material behavior of the substrate, contact size, applied load and indentation depth. Only three variable are known afterwards, namely, indenter shape, plus load and depth…
In the framework of a deep geological radioactive waste disposal in France, the hydromechanical properties of the designated host rock, the Callovo-Oxfordian claystone (COx), are investigated in laboratory tests. Experiments presented in…