Related papers: Dynamic Sensitivity Study of MEMS Capacitive Accel…
This paper presents the design, simulation, and analytical modeling of the single proposed axis MEMSbased capacitive accelerometer. Analytical modeling has been done for frequency and displacement sensitivity. The performance of the…
Microelectromechanical systems (MEMS) gyroscopes are widely used, e.g. in modern automotive and consumer applications, and require signal stability and accuracy in rather harsh environmental conditions. In many use cases, device reliability…
In this paper, the nonlinear squeeze-film damping (SFD) involving rarefied gas effect in the micro-electro-mechanical-systems (MEMS) is investigated. Considering the motion of structures (beam, cantilever, and membrane) in MEMS, the dynamic…
Understanding microstructural evolution under extreme thermal conditions is essential for advancing metal additive manufacturing (AM). This work demonstrates the feasibility of employing micro-electro-mechanical system (MEMS) heating…
This paper describes a temperature sensitivity or thermal sag measurement of a geometric anti-spring based micro-electromechanical system (MEMS) gravimeter (Wee-g). The Wee-g MEMS gravimeter is currently fabricated on a (100) silicon wafer…
An extremely sensitive temperature measurement MEMS device is developed based on the principle of structural deflection in a bi-material cantilever caused by a difference in thermal expansion coefficients. A dual-beam asymmetrical geometry…
The importance of thermoelastic damping as a fundamental dissipation mechanism for small-scale mechanical resonators is evaluated in light of recent efforts to design high-Q micrometer- and nanometer-scale electro-mechanical systems (MEMS…
In this study the dynamic behaviour of perforated microplates oscillating under the effect of squeeze film damping is analyzed. A numerical approach is adopted to predict the effects of damping and stiffness transferred from the surrounding…
High-quality polycrystalline SmFeAsO0.75 was synthesized with a superconducting transition width less than 1 K, and the electronic behavior was systematically studied by transport and specific heat measurements. An obvious superconducting…
Active microelectromechanical systems can couple the nanomechanical domain with the electronic domain by integrating electronic sensing and actuation mechanisms into the micromechanical device. This enables very fast and sensitive…
We study the dynamics of MEMS microbeams undergoing electrostatic pull-in. At DC voltages close to the pull-in voltage, experiments and numerical simulations have reported `bottleneck' behaviour in which the transient dynamics slow down…
We report on low temperature measurements performed on micro-electro-mechanical systems (MEMS) driven deeply into the non-linear regime. The materials are kept in their elastic domain, while the observed non-linearity is purely of…
Properties of typical MEMS materials have been widely investigated. Mechanical properties of MEMS structures depend not only on the bulk material properties, but also structural factors. A measurement system has been made to measure…
Micro-electro mechanical systems (MEMS) thermal flow sensors are increasingly used for compact, low-power flow monitoring in biomedical applications. However, silicon-based method for sensor fabrication is limited by high cost, rigidity,…
We present mechanical measurements performed at low temperatures on cantilever-based microelectro-mechanicalstructures(MEMS) coated with a metallic layer. Two very different coatings are presented in order to illustrate the capabilities of…
This study presents the design, fabrication, and test of a micro accelerometer with intrinsic processing capabilities, that integrates the functions of sensing and computing in the same MEMS. The device consists of an inertial mass…
Cryogenic characterization of transition-edge sensor (TES) bolometers is a time- and labor-intensive process. As new experiments deploy larger and larger arrays of TES bolometers, the testing process will become more of a bottleneck. Thus…
We report on an optimized micro-machined thermal flow-rate sensor as part of an autonomous multi-parameter sensing device for water network monitoring. The sensor has been optimized under the following constraints: low power consumption and…
The next generation of Far-infrared and X-ray space observatories will require detector arrays with thousands of transition edge sensor (TES) pixel. It is extremely important to have a tool that is able to characterize all the pixels and…
The solidification behavior of a eutectic AlCu specimen is investigated via in situ scanning transmission electron microscope (STEM) experiments. Solidification conditions are varied by imposing various cooling conditions via a…