Related papers: Length-scale cascade and spread rate of atomizing …
The spreading of a cap-shaped spherical droplet of non-Newtonian power-law liquids on a completely wettable spherical substrate is theoretically studied. Both convex spherical substrates and concave spherical cavities with smooth or rough…
Existing energy balance models, which estimate maximum droplet spreading, insufficiently capture the droplet spreading from low to high Weber and Reynolds numbers and contact angles. This is mainly due to the simplified definition of the…
The oscillatory flow around a spherical object lying on a rough bottom is investigated by means of direct numerical simulations of continuity and Navier-Stokes equations. The rough bottom is simulated by a layer/multiple layers of spherical…
The dynamics of drop impact on a rigid surface -- omnipresent in nature and technology -- strongly depends on the droplet's velocity, its size, and its material properties. The main characteristics are the droplet's force exerted on the…
Liquid drops start spreading directly after brought into contact with a partial wetting substrate. Although this phenomenon involves a three-phase contact line, the spreading motion is very fast. We study the initial spreading dynamics of…
In the present study, detailed numerical simulations are performed to investigate the primary breakup of a gasoline surrogate jet under non-evaporative "Spray G" operating conditions. The Spray G injector and operating conditions, developed…
This study employs molecular dynamics simulations to investigate droplet dynamics when a stationary droplet on a solid surface is struck by another droplet of similar size from above. The focus is on the jumping behavior of the merged…
The ambient gas pressure is determined for the onset of splashing of low-viscosity liquid drops on smooth dry surfaces as we change the control parameters: drop impact velocity, drop radius, viscosity, surface tension, density, and gas…
There is a need for experimental data in conditions representative injection in rocket engines to validate or initiate droplet formation models used in numerical simulations. A new cryogenic vessel was built upon the MASCOTTE test bench to…
We study the spreading of droplets in a near-critical phase-separated liquid mixture, using a combination of experiments, lubrication theory and finite-element numerical simulations. The classical Tanner's law describing the spreading of…
Numerical simulations describing plunging breakers including the splash-up phenomenon are presented. The motion is governed by the classical, incompressible, two-dimensional Navier-Stokes equation. The numerical modelling of this two-phase…
We provide an ab-initio scaling analysis for liquid film thickness and Nusselt number of a steady laminar jet impacting a rotating heated plate. The limiting scaling regimes incorporating the evaporative effects along the liquid-vapor…
Studies in the literature on plane turbulent wall jets on flat surfaces, have invariably considered either the nozzle initial conditions or the asymptotic conditions far downstream, as scaling parameters for the streamwise variations of…
We study spreading dynamics of nematic liquid crystal droplets within the framework of the long-wave approximation. A fourth order nonlinear parabolic partial differential equation governing the free surface evolution is derived. The…
In this article, we experimentally investigate the impact of a submillimetric water jet on a horizontal surface heated well above the "static" Leidenfrost temperature of water. We observe the transition from a regime where a single drop…
We experimentally investigate the deformation and breakup of droplets interacting with an oblique continuous air stream. A high-speed imaging system is employed to record the trajectories and topological changes of the droplets of different…
We introduce a numerical strategy to study the evolution of 2D water waves in the presence of a plunging jet. The free-surface Navier-Stokes solution is obtained with a finite but small viscosity. We observe the formation of a surface…
In liquid spray applications, the sprays are often created by the formation and destabilization of a liquid sheet or jet. The disadvantage of such atomization processes is that the breakup is often highly irregular, causing a broad…
Spray formation in ambient atmosphere from gas-centered swirl coaxial atomizers is described by carrying out experiments in a spray test facility. The atomizer discharges a circular air jet and an axisymmetric swirling water sheet from its…
Breakup of a liquid jet into a chain of droplets is common in nature and industry. Previous researchers developed profound mathematic and fluid dynamic models to address this breakup phenomenon starting from tiny perturbations. However, the…