Related papers: Codebook Design for Channel Feedback in Lens-Based…
Millimeter wave (mmWave) communication by utilizing lens antenna arrays is a promising technique for realizing cost-effective 5G wireless systems with large MIMO (multiple-input multiple-output) but only limited radio frequency (RF) chains.…
Beamspace multi-input multi-output (MIMO) relying on lens antenna arrays can significantly reduce the number of radio-frequency chains in millimeter-wave (mmWave) communication systems through beam selection. However, the beamforming gain…
Reconfigurable distributed antenna and reflecting surface (RDARS) is a new architecture for the sixth-generation (6G) millimeter wave (mmWave) communications. In RDARS-aided mmWave systems, the active and passive beamforming design and…
In pursuance of the unused spectrum in higher frequencies, millimeter wave (mmWave) bands have a pivotal role. However, the high path-loss and poor scattering associated with mmWave communications highlight the necessity of employing…
Channel estimation is challenging for millimeter-wave (mmWave) massive MIMO with hybrid precoding, since the number of radio frequency (RF) chains is much smaller than that of antennas. Conventional compressive sensing based channel…
Millimeter wave (mmWave) systems will likely employ directional beamforming with large antenna arrays at both the transmitters and receivers. Acquiring channel knowledge to design these beamformers, however, is challenging due to the large…
In this paper, we develop a low-complexity channel estimation for hybrid millimeter wave (mmWave) systems, where the number of radio frequency (RF) chains is much less than the number of antennas equipped at each transceiver. The proposed…
Millimeter wave (mmWave) signals experience orders-of-magnitude more pathloss than the microwave signals currently used in most wireless applications. MmWave systems must therefore leverage large antenna arrays, made possible by the…
The recent concept of beamspace multiple input multiple output (MIMO) can significantly reduce the number of required radio-frequency (RF) chains in millimeter-wave (mmWave) massive MIMO systems without obvious performance loss. However,…
The focus of this paper is on multi-user MIMO transmissions for millimeter wave systems with a hybrid precoding architecture at the base-station. To enable multi-user transmissions, the base-station uses a cell-specific codebook of…
In millimeter wave (mmWave) communication systems, beamforming with large antenna arrays is critical to overcome high path losses. Separating all-digital beamforming into analog and digital stages can provide the large reduction in power…
Extremely large-scale reconfigurable intelligent surface (XL-RIS) can effectively overcome severe fading and provide higher communication performance. However, current research on XL-RIS overlooks the discrete phase-shift characteristics of…
Millimeter-wave and terahertz systems rely on beamforming/combining codebooks to determine the best beam directions during the initial access and data transmission. Existing approaches suffer from large codebook sizes and high beam…
Millimeter wave (mmWave) is a practical solution to provide high data rate for the vehicle-to-everything (V2X) communications. This enables the future autonomous vehicles to exchange big data with the base stations (BSs) such as the…
The millimeter-wave (mmWave) communication is envisioned to provide orders of magnitude capacity improvement. However, it is challenging to realize a sufficient link margin due to high path loss and blockages. To address this difficulty, in…
Millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) has been regarded to be an emerging solution for the next generation of communications, in which hybrid analog and digital precoding is an important method for reducing…
Millimeter wave (mmWave) communication is one feasible solution for high data-rate applications like vehicular-to-everything communication and next generation cellular communication. Configuring mmWave links, which can be done through…
The channel state information (CSI) needs to be fed back from the user equipment (UE) to the base station (BS) in frequency division duplexing (FDD) multiple-input multiple-output (MIMO) system. Recently, neural networks are widely applied…
The potential advantages of intelligent wireless communications with millimeter wave (mmWave) and massive multiple-input multiple-output (MIMO) are based on the availability of instantaneous channel state information (CSI) at the base…
To fully unlock the benefits of multiple-input multiple-output (MIMO) networks, downlink channel state information (CSI) is required at the base station (BS). In frequency division duplex (FDD) systems, the CSI is acquired through a…