Related papers: Yielding Transitions and Grain-Size Effects in Dis…
The thermodynamic dislocation theory presented in preceding papers is used here to describe shear-banding instabilities. Central ingredients of the theory are a thermodynamically defined effective configurational temperature, and a formula…
We modify a theory of flow stress introduced in [arXiv:1803.08247[cond-mat.mtrl-sci]], [arXiv:1809.03628[cond-mat.mes-hall]], [arXiv:1908.09338[cond-mat.mtrl-sci]] for a class of polycrystalline materials with equilibrium and…
The thermodynamic dislocation theory developed for non-uniform plastic deformations is used here for the analysis of twisted copper wires. With a small set of physical parameters that we expect to be independent of strain rate and…
The thermodynamic theory of dislocation/grain boundary interaction, including dislocation pile-up against, absorption by, and transfer through the grain boundary, is developed for nonuniform plastic deformations in polycrystals. The case…
Thermodynamic dislocation theory incorporating dislocation impediment by the grain boundaries is developed to analyze the shear test of polycrystals. With a small set of physics based material parameters, we are able to simulate the…
We elaborate the recently introduced theory of flow stress, including yield strength, in polycrystalline materials under quasi-static plastic deformations, thereby extending the case of single-mode aggregates to multimodal ones in the…
We reformulate the theory of polycrystalline plasticity, in externally driven, nonequilibrium situations, by writing equations of motion for the flow of energy and entropy associated with dislocations. Within this general framework, and…
The effect of slip transfer on the flow strength of various FCC polycrystals was analyzed by means of computational homogenization of a representative volume element of the microstructure. The crystal behavior was governed by a…
A continuum theory based on thermodynamics has been developed for modeling diffusional creep of polycrystalline solids. It consists of a coupled problem of vacancy diffusion and mechanics where the vacancy generation/absorption at grain…
Starting from the assumption that all possible orientations of grains are equally probable, we prove that the geometric factor of thermodynamic dislocation theory for polycrystals subjected to axially symmetric tension or compression must…
The Hall-Petch effect has been described for the past sixty years as a dependence of the strength of polycrystalline metals on the inverse square-root of grain size d. The value of the coefficient of the dependence has been the subject of…
We show that the thermodynamic dislocation theory (TDT) predicts a scaling relation between stresses, strain rates, and temperatures for steady-state deformations of crystalline solids, and that this relation is accurately obeyed by a wide…
A theory of flow stress (FS), reviewing and developing our research,e.g. arxiv:1803.08247;1908.09338, is proposed,including yield strength (YS) of PC materials for quasi-static plastic loading for grain of average size d in range…
The mechanical behaviors of polycrystalline solids are determined by the interplay between phenomena governed by two different thermodynamic temperatures: the configurational effective temperature that controls the density of dislocations,…
The dynamics of dislocation assemblies in deforming crystals indicate the emergence of collective phenomena, intermittent fluctuations and strain avalanches. In polycrystalline materials, the understanding of plastic deformation mechanisms…
In the framework of the suggested in [arxiv:1803.08247 [cond-mat.mtrl-sci]] statistical theory of the equilibrium flow stress, including yield strength, ${\sigma}_y$, of polycrystalline materials under quasi-static (in case of tensile…
The statistical theory of flow stress, including yield strength, for polycrystalline materials under quasi-static plastic deformation suggested in [arxiv:1803.08247[cond-mat.mtr-sci], arxiv:1805.08623[cond-mat.mtr-sci]] is developed in the…
The effect of grain size on the flow stress of FCC polycrystals is analyzed by means of a multiscale strategy based on computational homogenization of the polycrystal aggregate. The mechanical behavior of each crystal is given by a…
A theory of flow stress, including the yield strength is proposed for the class of PC materials with equilibrium defect structure (EDS), which is established in the PC material after series of $N_0$ similar treatments of severe plastic…
Alloying metals with other elements is often done to improve the material strength or hardness. A key microscopic mechanism is precipitation hardening, where precipitates impede dislocation motion, but the role of such obstacles in…