Related papers: Fatigue Deformation of Polycrystalline Cu Using Mo…
Recently, a dislocation free deformation mechanism was proposed by Kiritani et al., based on a series of experiments where thin foils of fcc metals were deformed at very high strain rates. In the experimental study, they observed a large…
A framework based on FFT is proposed for micromechanical fatigue modeling of polycrystals as alternative to the Finite Element method (FEM). The variational FFT approach is used with a crystal plasticity model for the cyclic behavior of the…
Revealing statistics of H-defect interactions provides insights into significant ductility loss due to the particular strain partitioning in H-charged structural alloys. Experimental investigation of these interactions is extremely…
The article presents the results of corrosion-fatigue tests of industrial Al-Mg alloys were conducted in air and in a 3% NaCl aqueous solution. Fatigue curves can be characterized using the Basquin equation and the plastic deformation model…
Rock geophysical properties are widely reported to exhibit non-linear behaviours under low-stress conditions (below 10-20 MPa) before transitioning to the linear elastic stage, primarily due to the closure of microcracks and grain…
Fatigue caused by cyclic bending of a piece of material, resulting in its mechanical failure, is a phenomenon that had been studied for ages by engineers and physicists alike. In this Letter we study such fatigue in a strip of athermal…
We performed a series of numerical vertical compression tests on assemblies of 2D granular material using a Discrete Element code and studied the results with regard to the grain shape. The samples consist of 5,000 grains made from either 3…
In the framework of the suggested in [arxiv:1803.08247 [cond-mat.mtrl-sci]] statistical theory of the equilibrium flow stress, including yield strength, ${\sigma}_y$, of polycrystalline materials under quasi-static (in case of tensile…
Fatigue fracture is one of the main causes of failure in structures. However, the simulation of fatigue crack growth is computationally demanding due to the large number of load cycles involved. Metals in the low cycle fatigue range often…
We investigate the formation of stress hotspots in polycrystalline materials under uniaxial tensile deformation by integrating full field crystal plasticity based deformation models and machine learning techniques to gain data driven…
Molecular dynamics (MD) simulations are employed to investigate the capillary fluctuations of steps on the surface of a model metal system. The fluctuation spectrum, characterized by the wave number ($k$) dependence of the mean squared…
The exploitation of mineral resources in plateau regions is confronted with critical challenges including low blasting efficiency, excessive energy consumption,and compromised operational safety when dealing with low-temperature…
Dislocation jogs have strong effects on dislocation motion that governs the strain-hardening behavior of crystalline solids, but how to properly account for their effect in mesoscale models remains poorly understood. We develop a mobility…
With increasing interest in the use of glassy carbon (GC) for a wide variety of application areas, the need for developing fundamental understanding of its mechanical properties has come to the forefront. Further, recent theoretical and…
The hysteretic behavior exhibited by collagen fibrils, when subjected to cyclic loading, is known to result in both dissipation as well as accumulation of residual strain. On subsequent relaxation, partial recovery has also been reported.…
It is shown here that fracture after a brief plastic strain, typically of a few percents, is a necessary consequence of the polycrystalline nature of the materials. The polycrystal undergoing plastic deformation is modeled as a flowing…
The effect of alternating shear orientation during cyclic loading on the relaxation dynamics in disordered solids is examined using molecular dynamics simulations. The model glass was initially prepared by rapid cooling from the liquid…
Thermodynamic dislocation theory incorporating dislocation impediment by the grain boundaries is developed to analyze the shear test of polycrystals. With a small set of physics based material parameters, we are able to simulate the…
Dislocation slip is a general deformation mode and governs the strength of metals. Via discrete dislocation dynamics and molecular dynamics simulations, we investigate the strain rate and dislocation density dependence of the strength of…
Current transport in polysilicon is a complicated process with many factors to consider. The inhomogeneous nature of polysilicon with its differently shaped and sized grains is one such consideration. We have developed a method that…