Related papers: Calibration setup for ultralow-current transresist…
The knowledge of capacitance in semiconductor micro-strip detectors is important for a correct design, simulation and understanding of the detectors. Analytical approaches can efficiently complement numerical methods providing quick results…
The calibration technique for accelerometers has been internationally developed for up to 20 kHz to ensure the reliability of vibration measurement. However, it has been established that the calibrated sensitivity changes at over 10 kHz…
A new method is introduced for calibrating lateral force as measured by an atomic force microscope (AFM), making use of both an interferometric detector and an optical beam detector on the same instrument. The method may be implemented…
This paper demonstrates designing and developing of an Ultra-Low Noise Amplifier which should potentially increase the sensitivity of the existing Magnetic Resonance Imaging (MRI) systems. The Design of the LNA is fabricated and…
In this paper, a two-stage ultra-low-power operational amplifier is designed, and a comparative analysis of the proposed subthreshold complementary amplifier is presented between 180nm, 90nm, and 45nm CMOS technology. The proposed…
We present a method for absolute calibration of received radio-frequency in the ultra low frequency (ULF), and very low frequency (VLF) range. This is achieved with the use of a radio frequency optically pumped magnetometer (RF-OPM). We…
Acoustic cameras have found many applications in practice. Accurate and reliable extrinsic calibration of the microphone array and visual sensors within acoustic cameras is crucial for fusing visual and auditory measurements. Existing…
This paper deals with the challenge of short-circuit calculation for power systems dominated by power electronics converters. A novel methodology has been presented to identify short-circuit equilibrium point of the studied system…
We generalize solid-state tight-binding techniques for the spectral analysis of large superconducting circuits. We find that tight-binding states can be better suited for approximating the low-energy excitations than charge-basis states, as…
We use a piezoelectric quartz tuning fork to calibrate the displacement of ceramic piezoelectric scanners which are widely employed in scanning probe microscopy. We measure the static piezoelectric response of a quartz tuning fork and find…
We describe the commissioning of a system which has been built to investigate optimal operation of CCDs for the LSST telescope. The test system is designed for low vibration, high stability operation and is capable of illuminating a…
The two output signals of quadrature phase interferometers allow to benefit both from the high sensitivity of interferometry (working inside a fringe) and from an extended input range (counting fringes). Their calibration to reach a linear…
The capacitance of the charge collection node of a sensor system is an important parameter for the design of the analog front-end electronics. The analog front-end of high-granularity sensors like for example hybrid pixel detectors need to…
The requirements and details of designing a measuring cell and low-back-action deeply-cooled amplifier for quantum measurements at 10 mK are discussed. This equipment is a part of a microwave single-photon counter based on a superconducting…
As quantum systems expand in size and complexity, manual qubit characterization and gate optimization will be a non-scalable and time-consuming venture. Physical qubits have to be carefully calibrated because quantum processors are very…
This paper describes the design of a low-cost USB-controlled potentiostat/galvanostat which can measure or apply potentials in the range of +/-8V, and measure or apply currents ranging from nanoamps to max. +/-25 mA. Precision is excellent…
Accurate in situ calibration of microwave attenuation and amplification-chain noise is essential for superconducting quantum circuits. We demonstrate a compact, self-calibrating cryogenic noise source based on an on-chip chromium attenuator…
Low-cost micro-electromechanical accelerometers are widely used in navigation, robotics, and consumer devices for motion sensing and position estimation. However, their performance is often degraded by bias errors. To eliminate…
This paper presents a detailed description, analysis and example of practical application of a wide frequency band voltage-to-current converter. The converter is characterized by a combination of positive and negative feedback loops. This…
Conventional computers have evolved to device components that demonstrate failure rates of 1e-17 or less, while current quantum computing devices typically exhibit error rates of 1e-2 or greater. This raises concerns about the reliability…