Related papers: Manufacturing and testing a thin glass mirror shel…
The addition of an optically absorptive layer to otherwise standard dielectric mirrors enables a set of laser direct writing nanostructuring methods that can add functionality to such mirrors while retaining their high reflectivity. These…
We designed 4x4 matrix TFTs arrays using current mirror amplifiers. Advantages of current mirror amplifiers are they need less requiring switches and the conversion time is short. The TFTs arrays 4x4 matrix using current mirror circuits…
The advent of ultrahigh-power femtosecond lasers creates a need for optical components suitable to handle ultrahigh light intensities. Due to the unavoidable laser-induced ionization of matter, these components will have to be based on a…
We introduce a microscopy technique that facilitates the prediction of spatial features of chirality of nanoscale samples by exploiting photo-induced optical force exerted on an achiral tip in the vicinity of the test specimen. The…
We report the first results from an X-ray polarimeter with a micropattern gas proportional counter using an amorphous silicon active matrix readout. With 100% polarized X-rays at 4.5 keV, we obtain a modulation factor of 0.33 +/- 0.03,…
Recent advances in grazing incidence X-ray optics using synchrotron radiation sources have stimulated the need for basic research in high quality mirror materials for novel applications. In this paper we communicate the results of the first…
We report on the production of an array of active edge silicon sensors as a prototype of a large array. Four Medipix3RX.1 chips were bump bonded to four single chip sized Advacam active edge n-on-n sensors. These detectors were then mounted…
This paper demonstrates a cryogenic deformable mirror (DM) with 1,020 actuators based on micro-electrical mechanical systems (MEMS) technology. Cryogenic space-borne infrared telescopes can experience a wavefront error due to a figure error…
Coronagraph instruments on future space telescopes will enable the direct detection and characterization of Earth-like exoplanets around Sun-like stars for the first time. The quest for the optimal optical coronagraph designs has made rapid…
We have designed and tested experimentally a morphing structure consisting of a neutrally stable thin cylindrical shell driven by a multiparameter piezoelectric actuation. The shell is obtained by plastically deforming an initially flat…
$V_2O_3$ has long been studied as a prototypical strongly correlated material. The difficulty in obtaining clean, well ordered surfaces, however, hindered the use of surface sensitive techniques to study its electronic structure. Here we…
We present the design and operation of a fiber-based cryogenic confocal microscope. It is designed as a compact cold-finger that fits inside the bore of a superconducting magnet, and which is a modular unit that can be easily swapped…
We present a tactile sensing method enabled by the mechanical compliance of soft robots; an externally attachable photoreflective module reads surface deformation of silicone skin to estimate contact force without embedding tactile…
Cherenkov threshold detectors (XCET) are used for identifying particles in the experimental areas at CERN. These detectors observe Cherenkov light emitted by charged particles travelling inside a pressurized gas vessel. A key component of…
Optical tweezers have been widely used for optical manipulation of various particles. At present, there are different type of optical tweezers. Among them, holographic optical tweezers have attracted growing attention as a powerful tools…
Optical activity (polarization rotation of light) is one of the most desired features of chiral media, as it is important for many polarization related applications. However, in the THz region, chiral media with strong optical activity are…
Additive manufacturing (AM; 3D printing) has clear benefits in the production of lightweight mirrors for astronomy: it can create optimised lightweight structures and combine multiple components into one. New capabilities in AM ceramics,…
Electrically-driven soft robots based on piezoelectric actuators may enable compact form factors and maneuverability in complex environments. In most prior work, piezoelectric actuators are used to control a single degree of freedom. In…
Miniaturized optical imaging systems typically utilize 2-dimensional (2D) actuators to acquire images over a 2D field of view (FOV). Piezoelectric tubes are most compact, but usually produce sub-millimeter FOVs and are difficult to…
In the context of the Large Binocular Telescope project, we present the results of force actuator calibrations performed on an adaptive secondary prototype called P45, a thin deformable glass with magnets glued onto its back.…