Related papers: Energy consistent framework for continuously evolv…
The elastic response of the crystalline sheet to the stretching deformation in the form of wrinkles has been extensively investigated. In this work, we extend this fundamental scientific question to the plastic regime by exploring the…
This paper outlines a rigorous variational-based multilevel Global-Local formulation for ductile fracture. Here, a phase-field formulation is used to resolve failure mechanisms by regularizing the sharp crack topology on the local state.…
Brittle solids are often toughened by adding a second-phase material. This practice often results in composites with material heterogeneities on the meso scale: large compared to the scale of the process zone but small compared to that of…
Statistical models are essential to get a better understanding of the role of disorder in brittle disordered solids. Fiber bundle models play a special role as a paradigm, with a very good balance of simplicity and non-trivial effects. We…
We study Mode I crack propagation in amorphous material via a molecular dynamics simulation of a binary alloy with pairwise central-force interactions. We find that when the system is subjected to constant displacement after introduction of…
Crack front waves (FWs) are dynamic objects that propagate along moving crack fronts in 3D materials. We study FW dynamics in the framework of a 3D phase-field framework that features a rate-dependent fracture energy $\Gamma(v)$ ($v$ is the…
In this work, distortion gradient plasticity is used to gain insight into material deformation ahead of a crack tip. This also constitutes the first fracture mechanics analysis of gradient plasticity theories adopting Nye's tensor as primal…
Despite extensive theoretical treatment of short- to long-crack transitions, direct experimental quantification of how elastic and plastic energy contributions evolve at the crack tip during arrest has remained absent. In this study, we…
Reduction of computational cost of solutions is a key issue to crack identification or crack propagation problems. One of the solution is to avoid re-meshing the domain when the crack position changes or when the crack extends. To avoid…
Fracture of materials with rate-dependent mechanical behaviour, e.g. polymers, is a highly complex process. For an adequate modelling, the coupling between rate-dependent stiffness, dissipative mechanisms present in the bulk material and…
We introduce a model of fracture which includes the out-of-plane degrees of freedom necessary to describe buckling in a thin-sheet material. The model is a regular square lattice of elastic beams, rigidly connected at the nodes so as to…
We examine the effect of small, spatially localized, excitations applied periodically in different manners, on the crackling dynamics of a brittle crack driven slowly in a heterogeneous solid. When properly adjusted, these excitations are…
We study the genesis and the selective propagation of complex crack networks induced by thermal shock or drying of brittle materials. We use a quasi-static gradient damage model to perform large scale numerical simulations showing that the…
A force balance condition to predict quasistatic crack paths in anisotropic brittle materials is derived from an analysis of diffuse interface continuum models that describe both short-scale failure inside a microscopic process zone and…
A simple nonlocal field theory of peridynamic type is applied to model brittle fracture. The fracture evolution is shown to converge in the limit of vanishing nonlocality to classic plane elastodynamics with a running crack. The kinetic…
The method of iterated conformal maps is developed for quasi-static fracture of brittle materials, for all modes of fracture. Previous theory, that was relevant for mode III only, is extended here to mode I and II. The latter require…
Conforming materials to rigid substrates with Gaussian curvature --- positive for spheres and negative for saddles --- has proven a versatile tool to guide the self-assembly of defects such as scars, pleats, folds, blisters, and liquid…
We report results on the interrelation between driving force, roughness exponent, branching and crack speed in a finite element model. We show that for low applied loadings the crack speed reaches the values measured in the experiments, and…
This paper is concerned with the problem of a semi-infinite crack steadily propagating in an elastic solid with microstructures subject to antiplane loading applied on the crack surfaces. The loading is moving with the same constant…
We formulate a nonlocal cohesive model for calculating the deformation state inside a cracking body. In this model a more complete set of physical properties including elastic and softening behavior are assigned to each point in the medium.…