Related papers: Hybrid Beamforming for Massive MIMO - A Survey
Hybrid beamforming is considered a key enabler to realize millimeter wave (mmWave) multiple-input multiple-output (MIMO) communications due to its capability of considerably reducing the number of costly and power-hungry radio frequency…
Millimeter wave (mmWave) MIMO will likely use hybrid analog and digital precoding, which uses a small number of RF chains to avoid energy consumption associated with mixed signal components like analog-to-digital components not to mention…
Increasing the number of transmit and receive elements in multiple-input-multiple-output (MIMO) antenna arrays imposes a substantial increase in hardware and computational costs. We mitigate this problem by employing a reconfigurable MIMO…
In this article we compare the performance of two typical hyrbid beamforming structures for multiuser massive MIMO systems, i.e., the full- and partial-connection structures. Under the assumption of small angular spread for mmWave channels,…
In this letter, we investigate the hybrid beamforming for millimeter wave massive multiple-input multiple-output (MIMO) system based on deep reinforcement learning (DRL). Imperfect channel state information (CSI) is assumed to be available…
Multicast beamforming is known to improve spectral efficiency. However, its benefits and challenges for hybrid precoders design in millimeter-wave (mmWave) systems remain understudied. To this end, this paper investigates the first joint…
Hybrid analog-digital (A/D) transceivers designed for millimeter wave (mmWave) systems have received substantial research attention, as a benefit of their lower cost and modest energy consumption compared to their fully-digital…
Downlink massive multiple-input multiple-output (MIMO) precoding algorithms in frequency division duplexing (FDD) systems rely on accurate channel state information (CSI) feedback from users. In this paper, we analyze the tradeoff between…
Massive multiple-input multiple-out (MIMO) technology is vital in millimeter-wave (mmWave) bands to obtain large array gains. However, there are practical challenges, such as high hardware cost and power consumption in such systems. A…
Hybrid transceiver design in multiple-input multiple-output (MIMO) Tera-Hertz (THz) systems relying on sparse channel state information (CSI) estimation techniques is conceived. To begin with, a practical MIMO channel model is developed for…
In this paper, adaptive hybrid beamforming methods are proposed for millimeter-wave range massive multiple-input-multiple-output (MIMO) systems considering single carrier wideband transmission in uplink data mode. A statistical analog…
Hybrid analog and digital beamforming transceivers are instrumental in addressing the challenge of expensive hardware and high training overheads in the next generation millimeter-wave (mm-Wave) massive MIMO (multiple-input multiple-output)…
Millimeter wave (mmWave) communications have been considered as a key technology for future 5G wireless networks. In order to overcome the severe propagation loss of mmWave channel, mmWave multiple-input multiple-output (MIMO) systems with…
In this paper, we study the channel estimation problem in correlated massive multiple-input-multiple-output (MIMO) systems with a reduced number of radio-frequency (RF) chains. Importantly, other than the knowledge of channel correlation…
Hybrid Massive MIMO reduces implementation complexity but only supports beamforming coefficients that are common across all subbands. However, in macro cellular where the channel has limited degrees of freedom, the long-term component of…
We consider a MIMO interference channel in which the transmitters and receivers operate in frequency-division duplex mode. In this setting, interference management through coordinated transceiver design necessitates channel state…
The cost of radio frequency (RF) chains is the biggest drawback of massive MIMO millimeter wave networks. By employing spatial modulation (SM), it is possible to implement lower number of RF chains than transmit antennas but still achieve…
At millimeter wave (mmWave) frequencies, the higher cost and power consumption of hardware components in multiple-input multiple output (MIMO) systems do not allow beamforming entirely at the baseband with a separate radio frequency (RF)…
Millimeter-wave (mmWave) communication operated in frequency bands between 30 and 300 GHz has attracted extensive attention due to the potential ability of offering orders of magnitude greater bandwidths combined with further gains via…
As a key technology to meet the ever-increasing data rate demand in beyond 5G and 6G communications, millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) systems have gained much attention recently.To make the most of…