Related papers: Reference Physics Design for 1 GeV Injector Linac …
We report the results of a recent beam dynamics study, motivated by the need to redesign the LCLS photoinjector, that lead to the discovery of a new effective working point for a split RF photoinjector. We consider the emittance…
The upgrade of the normal conducting (NC) Radioactive Ion Beam EXperiment (REX)-ISOLDE heavy ion accelerator at CERN, under the High Intensity and Energy (HIE)-ISOLDE framework, proposes the use of superconducting (SC) quarter-wave…
We present the baseline design of the electron ring collimation system for the Electron-Ion Collider (EIC) at Brookhaven National Laboratory (BNL). The system addresses beam losses in a high-current electron storage ring with…
During the initial phase of operation, the linacs of the Next Linear Collider (NLC) will contain roughly 5000 X-Band accelerator structures that will accelerate beams of electrons and positrons to 250 GeV. These structures will nominally…
As the second stage of the CEPC-SPPC project, SPPC (Super Proton-Proton Collider) aims at exploring new physics beyond the Standard Model. The key design goal for the SPPC accelerator complex is to reach 75 TeV in center of mass energy with…
To realize and test advanced accelerator concepts and hardware, a beamline is being reconfigured in the Linac Extension Area (LEA) of APS linac. A photo-cathode RF gun installed at the beginning of the APS linac will provide a low emittance…
The variety of beams, needed to set-up in the injectors as requested in the LHC, are reviewed, in terms of priority but also performance expectations and reach during 2015. This includes the single bunch beams for machine commissioning and…
A high precision beam monitor system based on silicon carbide PIN sensor is designed for China Spallation Neutron Source 1.6 GeV proton beam to monitor the proton beam fluence.The concept design of the beam monitor system is finished…
A conceptual design is presented of a novel ERL facility for the development and application of the energy recovery technique to linear electron accelerators in the multi-turn, large current and large energy regime. The main characteristics…
Project-X is a proposed project to be built at Fermi National Accelerator Laboratory with several potential missions. A primary part of the Project-X accelerator chain is a Superconducting linac, and In October 2009 a workshop was held to…
For some synchrotron light source beamline applications, a round beam is preferable to a flat one. A conventional method of obtaining round beam in an electron storage ring is to shift its tune close to a linear difference resonance. The…
A muon collider as well as a neutrino factory requires a large number of muons with a kinetic energy of 50GeV or more. Muon survival demands a high gradient linac. The large transverse and longitudinal emittance of the muon beam coming from…
The Pohang Accelerator Laboratory operates an electron linac for the pulsed neutron source as one of the long-term nuclear R&D programs at the Korea Atomic Energy Research Institute. The designed beam parameters are as follows; The nominal…
LINAC 4 is a normal conducting H- linac proposed at CERN to provide a higher proton flux to the CERN accelerator chain. It should replace the existing LINAC 2 as injector to the Proton Synchrotron Booster and can also operate in the future…
In order to dissipate long-lived radioactive waste, not only high ux proton accelerator but also electron linac have been proposed. A proton accelerator directly induces nuclear fission and mutation. On the other hand, electron beam has two…
Alignment of the ILC main linac will be more critical than for any currently existing accelerators due to its long length and the ultra low emittance required. There are several techniques for measuring the ILC reference network; in this…
For the CLIC two-beam scheme, a high-current, long-pulse drive beam is required for RF power generation. Taking advantage of the 3 GHz klystrons available at the LEP injector once LEP stops, a 180 MeV electron accelerator is being…
KEK-ATF is studying low emittance, multi-bunch electron beam for the future linear collider. The energy instability of the 1.5 GeV linac has been a problem making the beam injection to the damping ring unstable. Because the unstable beam…
A muon storage ring neutrino source uses an induction linac for muon capture, a 200 MHz copper cavity system for cooling, and 200 and 400 MHz superconducting rf systems for acceleration to a final energy of up to 50 GeV. These systems and…
The injector (Scheme-I) of the C-ADS linac is a 10-mA 10-MeV proton linac working in CW mode. It is mainly comprised of a 3.2-MeV room-temperature 4-vane RFQ and twelve superconducting single-spoke cavities housed in a long cryostat. Error…