Related papers: Actuator line modeling of vertical-axis turbines
In this work the accuracy of the Actuator Line Model (ALM) in Large Eddy Simulations of wind turbine flow is studied under the specific conditions of very coarse spatial resolutions. For finely-resolved conditions, it is known that ALM…
Numerical models of the flow and wakes due to turbines operating within a real-scale offshore wind farm can lead to a prohibitively large computational cost, particularly when considering blade-resolved simulations. With the introduction of…
We evaluate the accuracy of the actuator line model (ALM) approach by performing simulations for the NREL~5~MW wind turbine in uniform inflow using three large eddy simulation codes. The power and thrust coefficients obtained using the…
The near-wake of a vertical-axis cross-flow turbine (CFT) was modeled numerically via blade-resolved $k$-$\omega$ SST and Spalart-Allmaras RANS models in two and three dimensions. Results for each case are compared with experimental…
In many engineering and industrial applications, the investigation of rotating turbulent flow is of great interest. In rotor-stator cavities, the centrifugal and Coriolis forces have a strong influence on the turbulence by producing a…
Modelling of turbine blade-induced turbulence (BIT) is discussed within the framework of three-dimensional Reynolds-averaged Navier-Stokes (RANS) actuator disk computations. We first propose a generic (baseline) BIT model, which is applied…
Two configurations typical of fixed-wing aircraft are simulated with the actuator line method (ALM): a wing with winglets and a T-tail. The ALM is extensively used in rotor simulations to model the blades by body forces, which are…
We compare three different methodologies for simulation of turbulent flow past a vertical axis wind turbine: (i) full resolution of the turbine blades in a Direct Finite Element Simulation (DFS), (ii) implicit representation of the turbine…
Turbulent flow has been extensively studied using computational fluid dynamics (CFD) simulations since turbulent flow regime is so frequently encountered in both academic and engineering applications. The high-fidelity simulation of the…
Computational fluid dynamics (CFD) is a useful tool for prediction of turbulence in aerodynamic and biomedical applications. The choice of appropriate turbulence models is key to reaching accurate predictions. The present investigation…
We assess the suitability of Reynolds-Averaged Navier-Stokes (RANS) simulation using the Spallart-Almaras (SA) turbulence model as a closure in analysing the performance of fluidic Active Flow Control (AFC) applications. In particular, we…
The actuator line method (ALM) is extensively used in wind turbine and rotor simulations. However, its original uncorrected formulation overestimates the forces near the tip of the blades and does not reproduce well forces on translating…
This work determines the inaccuracy of using Reynolds averaged Navier Stokes (RANS) turbulence models in transition to turbulent flow regimes by predicting the model-based discrepancies between RANS and large eddy simulation (LES) models…
The actuator line model (ALM) is a commonly used method to represent lifting surfaces such as wind turbine blades within Large-Eddy Simulations (LES). In the ALM the lift and drag forces are replaced by an imposed body force which is…
Reynolds-Averaged Navier-Stokes(RANS) method will still play a vital role in the following several decade in aerospace engineering. Although RANS models are widely used, empiricism and large discrepancies between models reduce the…
A local artificial neural network (LANN) framework is developed for turbulence modeling. The Reynolds-averaged Navier-Stokes (RANS) unclosed terms are reconstructed by artificial neural network (ANN) based on the local coordinate system…
Despite the increasing availability of high-performance computational resources, Reynolds-Averaged Navier-Stokes (RANS) simulations remain the workhorse for the analysis of turbulent flows in real-world applications. Linear eddy viscosity…
The actuator line method (ALM) is an approach commonly used to represent lifting and dragging devices like wings and blades in large-eddy simulations (LES). The crux of the ALM is the projection of the actuator point forces onto the LES…
Actuator line model has been widely employed in wind turbine simulations. However, the standard actuator line model does not include a model for the turbine nacelle which can significantly impact turbine wake characteristics as shown in the…
Predictive simulation of many complex flows requires moving beyond Reynolds-averaged Navier-Stokes (RANS) based models to representations resolving at least some scales of turbulence in at least some regions of the flow. To resolve…