Related papers: Hybrid Analog-Digital Precoding Revisited under Re…
Hybrid analog-digital precoding is a key millimeter wave access technology, where an antenna array with reduced number of radio frequency (RF) chains is used with an RF precoding matrix to increase antenna gain at a reasonable cost.…
For 5G it will be important to leverage the available millimeter wave spectrum. To achieve an approximately omni- directional coverage with a similar effective antenna aperture compared to state of the art cellular systems, an antenna array…
Due to heavy reliance of millimeter-wave (mmWave) wireless systems on directional links, Beamforming (BF) with high-dimensional arrays is essential for cellular systems in these frequencies. How to perform the array processing in a power…
Conventional hybrid beamforming architectures are often compared with one another and with the fully-digital architecture under the same \emph{radiated} antenna power. However, the physically relevant budget is the power injected by the…
For 5G it will be important to leverage the available millimeter wave spectrum. To achieve an approximately omni- directional coverage with a similar effective antenna aperture compared to state of the art cellular systems, an antenna array…
Massive multiple-input multiple-output (MIMO) avails of simple transceiver design which can tackle many drawbacks of relay systems in terms of complicated signal processing, latency, and noise amplification. However, the cost and circuit…
The conventional digital beamforming technique needs one radio frequency (RF) chain per antenna element. High power consumption, significantly high cost of RF chain components per antenna and complex signal processing task at base band…
Modern wireless communication networks, particularly cellular networks utilize multiple antennas to improve the capacity and signal coverage. In these systems, typically an active transceiver is connected to each antenna. However, this…
This paper considers the discrete Fourier transform (DFT) based hybrid beamforming multiuser system and studies the use of analog beam selection schemes. We first analyze the uplink ergodic achievable rates of the zero-forcing (ZF) receiver…
Due to the heavy reliance of millimeter-wave (mmWave) wireless systems on directional links, beamforming (BF) with high-dimensional arrays is essential for cellular systems in these frequencies. How to perform the array processing in a…
This paper considers hybrid beamforming (HB) for downlink multiuser massive multiple input multiple output (MIMO) systems with frequency selective channels. For this system, first we determine the required number of radio frequency (RF)…
This paper proposes a hybrid beamforming framework for massive multiple-input multiple-output (MIMO) in near-space airship-borne communications. To achieve high energy efficiency (EE) in energy-constraint airships, a dynamic subarray…
This paper studies energy-efficient hybrid beamforming architectures and its algorithm design in millimeter-wave communication systems, aiming to address the challenges faced by existing hybrid beamforming due to low hardware flexibility…
The potential of using of millimeter wave (mmWave) frequency for future wireless cellular communication systems has motivated the study of large-scale antenna arrays for achieving highly directional beamforming. However, the conventional…
In this work, we investigate hybrid analog-digital beamforming (HBF) architectures for uplink cell-free (CF) millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) systems. {We first propose two HBF schemes, namely,…
In this correspondence, we analytically characterize the benefit of digital processing in uplink massive multiple-input multiple-output (MIMO) with sub-connected hybrid architecture. By assuming that the number of radio frequency (RF)…
In massive MIMO systems, hybrid beamforming is an essential technique for exploiting the potential array gain without using a dedicated RF chain for each antenna. In this work, we consider the data phase in a massive MIMO communication…
The discrete Fourier transform (DFT) is widely employed for multi-beam digital beamforming. The DFT can be efficiently implemented through the use of fast Fourier transform (FFT) algorithms, thus reducing chip area, power consumption,…
In massive MIMO systems, fully digital precoding offers high performance but has significant implementation complexity and energy consumption, particularly at millimeter frequencies and beyond. Hybrid analog-digital architectures provide a…
6G networks are expected to provide more diverse capabilities than their predecessors and are likely to support applications beyond current mobile applications, such as virtual and augmented reality (VR/AR), AI, and the Internet of Things…