Related papers: Directional Beamforming for Millimeter-Wave MIMO S…
Millimeter wave (mmWave) has great potential in realizing high data rate thanks to the large spectral channels. It is considered as a key technology for the fifth generation wireless networks and is already used in wireless LAN (e.g., IEEE…
Motivated by massive deployment of low data rate Internet of things (IoT) and ehealth devices with requirement for highly reliable communications, this paper proposes receive beamforming techniques for the uplink of a single-input…
To support the high data rates for latency-critical applications, future wireless systems will employ fully digital beamforming multiple-input multiple-output (MIMO) architectures at millimeter wave (mmWave) frequencies. Moreover, mmWave…
Designing unimodular waveforms with a desired beampattern, spectral occupancy and orthogonality level is of vital importance in the next generation Multiple-Input Multiple-Output (MIMO) radar systems. Motivated by this fact, in this paper,…
Future cellular systems based on the use of above-6 GHz frequencies, the so-called millimeter wave (mmWave) bandwidths, will heavily rely on the use of antenna arrays both at the transmitter and at the receiver, possibly with a large number…
Massive multiple-input multiple-out (MIMO) technology is vital in millimeter-wave (mmWave) bands to obtain large array gains. However, there are practical challenges, such as high hardware cost and power consumption in such systems. A…
We present a beamforming algorithm for multiuser wideband millimeter wave (mmWave) communication systems where one access point uses hybrid analog/digital beamforming while multiple user stations have phased-arrays with a single RF chain.…
Beamforming is an indispensable feature for millimeter wave (mmWave) wireless communications in order to compensate for the severe path loss incurred due to high frequency operation. In this paper, we introduce a novel framework to evaluate…
The performance of millimeter wave (mmWave) multiple-input multiple-output (MIMO) systems is limited by the sparse nature of propagation channels and the restricted number of radio frequency (RF) chains at transceivers. The introduction of…
Future cellular systems based on the use of millimeter waves will heavily rely on the use of antenna arrays both at the transmitter and at the receiver. For complexity reasons and energy consumption issues, fully digital precoding and…
The millimeter-wave (mm-wave) bands enable very large antenna arrays that can generate narrow beams for beamforming and spatial multiplexing. However, directionality introduces beam misalignment and leads to reduced energy efficiency. Thus,…
In this paper, we propose a scheme called "beam-nulling" for MIMO adaptation. In the beam-nulling scheme, the eigenvector of the weakest subchannel is fed back and then signals are sent over a generated subspace orthogonal to the weakest…
This paper investigates the design of analog beamforming at the receiver in millimeter-wave (mmWave) multiple-input multiple-output (MIMO) systems, aided by full digital chains featuring 1-bit ADCs. We advocate utilizing these full digital…
Massive antenna arrays form physically large apertures with a beam-focusing capability, leading to outstanding wireless power transfer (WPT) efficiency paired with low radiation levels outside the focusing region. However, leveraging these…
With the increasing demand of ultra-high-speed wireless communications and the existing low frequency band (e.g., sub-6GHz) becomes more and more crowded, millimeter-wave (mmWave) with large spectra available is considered as the most…
In this letter, we consider optimal hybrid beamforming design to minimize the transmission power under individual signal-to-interference-plus-noise ratio (SINR) constraints in a multiuser massive multiple-input-multiple-output (MIMO)…
Hybrid beamforming is an emerging technology for massive multiple-input multiple-output (MIMO) systems due to the advantages of lower complexity, cost, and power consumption. Recently, intelligent reflection surface (IRS) has been proposed…
Millimeter-wave (mmwave) communication represents a potential solution to capacity shortage in vehicular networks. However, effective beam alignment between senders and receivers requires accurate knowledge of the vehicles' position for…
In this paper, randomly-directional beamforming (RDB) is considered for millimeter-wave (mmwave) multi-user (MU) multiple-input single-output (MISO) downlink systems. By using asymptotic techniques, the performance of RDB and the MU gain in…
This paper conceives a hybrid beamforming design (HBF) that maximizes the energy efficiency (EE) of an integrated sensing and communication (ISAC)-enabled millimeter wave (mmWave) multiple-input multiple-output (MIMO) system. In the system…