Related papers: Loading-unloading hysteresis loop of randomly roug…
Using as a starting point conservation of momentum, a multiphase mechanical energy balance equation is derived that accounts for multiple material phases and interfaces present within a moving control volume. This balance is applied to a…
Adhesive [e.g. van der Waals] forces were not generally taken into account in contact mechanics until 1971, when Johnson, Kendall and Roberts (JKR) generalized Hertz' solution for an elastic sphere using an energetic argument which we now…
Hysteresis is a general phenomenon regularly observed in measurements of various materials properties such as magnetism, elasticity, capillary pressure, adsorption, battery voltage etc. Usually, the hysteretic behaviour is an intrinsic…
The equilibrium contact angle of a droplet resting on a solid substrate can reveal essential properties of the solid's surface. However, when the motion of a droplet on a surface shows significant hysteresis, it is generally accepted that…
We present new micromagnetic simulations, where an influence of the wire shape on the spatial distribution of internal magnetoelastic stress is taken into account. Local magnetoelastic anisotropy is approximated to be uniaxial, with spatial…
Hysteresis is a special type of behavior encountered in physical systems: in a hysteretic system, when the input is periodic and varies slowly, the steady-state part of the output-versus-input graph becomes a loop called hysteresis loop. In…
Lubrication flows appear in many applications in engineering, biophysics, and in nature. Separation of surfaces and minimisation of friction and wear is achieved when the lubrication fluid builds up a lift force. In this paper we analyse…
Motivated by recent experimental studies of rheological hysteresis in soft glassy materials, we study numerically strain rate sweeps in simple yield stress fluids and viscosity bifurcating yield stress fluids. Our simulations of downward…
Contact angle hysteresis and generation of dynamics angle are two fundamental phenomena about the contact angle deviation from the equilibrium state. Roughness on the solid surface, disjoining pressure in the thin film, and liquid-solid…
The real area of contact governs, in part, the magnitude of the friction force, yet its time evolution in rough viscoelastic interfaces remains incompletely understood. In experiments of contact between polymethylmethacrylate blocks under…
Adhesion hysteresis can be caused by elastic instabilities that are triggered by surface roughness or chemical heterogeneity. However, the role of these instabilities in adhesion hysteresis remains poorly understood because we lack…
When two solids are squeezed together they will in general not make atomic contact everywhere within the nominal (or apparent) contact area. This fact has huge practical implications and must be considered in many technological…
Finite element methods are used to study non-adhesive, frictionless contact between elastic solids with self-affine surfaces. We find that the total contact area rises linearly with load at small loads. The mean pressure in the contact…
Within the framework of Lorentz model for description of viscoelastic medium the influence of deformational defect of the shear modulus is studied on melting of ultrathin lubricant film confined between the atomically flat solid surfaces.…
We present exact numerical results for the friction force and the contact area for a viscoelastic solid (rubber) in sliding contact with hard, randomly rough substrates. The rough surfaces are self-affine fractal with roughness over several…
We present a molecular dynamics study of the contact between a rigid solid with a randomly rough surface and an elastic block with a flat surface. The numerical calculations mainly focus on the contact area and the interfacial separation…
The load-area relation of rough surfaces is of great interest in tribology. For elastic-plastic solids with strain hardening, an incremental model is adopted to analyze the contact of rough surfaces, in which the contact is modeled by…
The wetting behaviour of surfaces is important for various applications like super-hydrophobic surfaces, enhanced oil recovery, mining of metal ores and anti-icing surfaces etc. For rough surfaces, which are the rule rather than the…
Surface roughness emerges naturally during mechanical removal of material, fracture, chemical deposition, plastic deformation, indentation, and other processes. Here, we use continuum simulations to show how roughness which is neither…
The effect of self-affine roughness on solid contact is examined with molecular dynamics and continuum calculations. The contact area and normal and lateral stiffnesses rise linearly with the applied load, and the load rises exponentially…