Related papers: Front-end electronics and data acquisition system …
By implementing machine learning at the network edge, edge learning trains models by leveraging rich data distributed at edge devices (e.g., smartphones and sensors) and in return endow on them capabilities of seeing, listening, and…
A time projection chamber (TPC) based on a gaseous chamber with micro pixel electrodes (micro-PIC) has been developed for measuring three-dimensional tracks of charged particles. The micro-PIC with a detection area of 10 cm square consists…
This thesis is concerned with data-aided (DA) scheme and CFO tracking for OFDM system. OFDM system model is developed first without CFO and then with CFO. The system performance is evaluated via simulation. The bit error rate (BER),…
Using multiple-input multiple-output (MIMO) with orthogonal frequency division multiplexing (OFDM) for integrated sensing and communication (ISAC) has attracted considerable attention in recent years. While most existing works focus on…
Development of readout electronics for Time Projection Chamber for a Linear Collider is ongoing under stringent requirements on high channel density, lowest possible power consumption and small material budget. In the studied TPC readout…
Downlink massive multiple-input multiple-output (MIMO) precoding algorithms in frequency division duplexing (FDD) systems rely on accurate channel state information (CSI) feedback from users. In this paper, we analyze the tradeoff between…
A number of modern millimeter, sub-millimeter, and far-infrared detectors are read out using superconducting microwave (1-10GHz) resonators. The main detector technologies are Transition Edge Sensors, read out using Microwave SQUID…
An upgrade of the near detector of the T2K long baseline neutrino oscillation experiment is currently being conducted. This upgrade will include two new Time Projection Chambers, each equipped with 16 charge readout resistive Micromegas…
The field of autonomous driving technology is rapidly advancing, with deep learning being a key component. Particularly in the field of sensing, 3D point cloud data collected by LiDAR is utilized to run deep neural network models for 3D…
Recently proposed splitting receivers, utilizing both coherently and non-coherently processed signals for detection, have demonstrated remarkable performance gain compared to conventional receivers in the single-antenna scenario. In this…
This article presents a distributed model-predictive control (MPC) design for real-time voltage control in power systems, including an online method to estimate the bus admittance matrix $\mathbf{Y}$ to let it be time-varying and unknown a…
This work is proposing and exploring the use of multichannel readout electronics, already used in quality assurance for gain uniformity studies, to measure the uniformity of the induction gap in GEM based detectors. The measurement will…
In this paper, to jointly estimate the frequency and the direction-of-arrival(DOA) of the narrowband far-field signals, a novel array receiver architecture is presented by the concept of the sub-Nyquist sampling techniques. In particular,…
The Internet of Things (IoT) could enable the development of cloud multiple-input multiple-output (MIMO) systems where internet-enabled devices can work as distributed transmission/reception entities. We expect that spatial multiplexing…
Due to their large power draws and increasing adoption rates, electric vehicles (EVs) will become a significant challenge for electric distribution grids. However, with proper charging control strategies, the challenge can be mitigated…
Place recognition is an important component for autonomous vehicles to achieve loop closing or global localization. In this paper, we tackle the problem of place recognition based on sequential 3D LiDAR scans obtained by an onboard LiDAR…
The Data Acquisition System of the LZ experiment, the 10-tonne dark matter detector to be installed at the Sanford Underground Research Facility (SURF), will collect signals from 788 photomultiplier tubes (PMTs). Because the signals from…
The BeEST experiment is a precision laboratory search for physics beyond the standard model that measures the electron capture decay of $^7$Be implanted into superconducting tunnel junction (STJ) detectors. For Phase-III of the experiment,…
T0 detector, based on Multi-gap Resistive Plate Chambers (MRPC) technology, is one of the key components in the External Target Experiment. Through precision measurements of the MRPC signals, timing of the beam impact on target can be…
Large detectors are often monitored at the channel level (drift time, collected charge, and hit maps), which validates hardware but not tracking performance. A wire-by-wire tracking efficiency diagnostic is presented for the Belle~II…