Related papers: Weak amplification and single-photon weak-coupling…

Weak measurement with a coherent state pointer and in combination with an orthogonal postselection can lead to a surprising amplification effect, and we give a fire-new physical mechanism about the weak measurement in order to understand…

Most studies for postselected weak measurement in optomechanical system focus on using a single photon as a measured system. However, we find that using weak coherent light instead of a single photon can also amplify the mirror's position…

An experimental proposal is presented in which dark port post-selection together with weak measurements are used to enlarge the radiation pressure effect of a single photon on a mechanical oscillator placed in the middle of a Fabry-Perot…

Weak measurement [1,19] combined with quantum delayed-choice experiment that use quantum beam splitter instead of the beam splitter give rise to a surprising amplification effect, i.e., counterintuitive negative amplification effect. We…

We revisit the scheme of single-photon weak-coupling optomechanics using post-selection, proposed by Pepper, Ghobadi, Jeffrey, Simon and Bouwmeester [Phys. Rev. Lett. 109, 023601 (2012)], by analyzing the exact solution of the dynamical…

We present a scheme for achieving amplification of the displacement of the mirror in optomechanical cavity using single-photon postselection where the mirror is initially prepared in squeezed coherent state. The amplification depends on the…

In this article we present an experimental proposal for the estimation of an optomechanical parameter in the presence of noise. The estimation is based on the technique of weak value amplification which can enlarge the radiation pressure…

Weak amplification is a signal enhancement technique which is used to measure tiny changes that otherwise cannot be determined because of technical limitations. It is based on the existence of a special type of interaction which couples a…

An interferometric arrangement is proposed in which the technique of weak value amplification is implemented in order to enlarge the effect of a single photon on the quadratures of a movable mirror of an optical cavity. The photon interacts…

We show that weak measurement can be used to "amplify" optical nonlinearities at the single- photon level, such that the effect of one properly post-selected photon on a classical beam may be as large as that of many un-post-selected…

We study the possibility of varying the measured lifetime of a decaying particle based on the technique of weak value amplification in which an additional filtering process called postselection is performed. Our analysis made in a direct…

The weak measurements based amplification of ultra-small phase was proposed in our previous work. Due to the technical imperfections, the ability of amplification is usually limited in practice. Here we introduce the concept of cascaded…

First, a misconception about the spectrum of a confined particle is evidentiated. Then, the results are shown to be incorrect by means of a counter-example, an explicit preparation for the probe is given that yields an arbitrary…

We analyze the photon statistics of a weakly driven optomechanical system and discuss the effect of photon blockade under single photon strong coupling conditions. We present an intuitive interpretation of this effect in terms of displaced…

Weak measurements in combination with post-selection can give rise to a striking amplification effect (related to a large "weak value"). We show that this effect can be understood by viewing the initial state of the pointer as the ground…

We consider the use of cyclic weak measurements to improve the sensitivity of weak-value amplification precision measurement schemes. Previous weak-value experiments have used only a small fraction of events, while discarding the rest…

Weak measurement is a new technique which allows one to describe the evolution of postselected quantum systems. It appears to be useful for resolving a variety of thorny quantum paradoxes, particularly when used to study properties of pairs…

The implementation of weak-value amplification requires the pre- and post-selection of states of a quantum system, followed by the observation of the response of the meter, which interacts weakly with the system. Data acquisition from the…

Optomechanical systems are often used for the measurement of weak forces. Feedback loops can be used in these systems for achieving noise reduction. Here we show that even though feedback is not able to improve the signal to noise ratio of…

We present a detailed theoretical analysis of a weakly driven multimode optomechanical system, in which two optical modes are strongly and near-resonantly coupled to a single mechanical mode via a three-wave mixing interaction. We calculate…